
The AirTAC SAID63 Double Rod Cylinder SAID63X180 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø63mm bore and 180mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID63X180 is a double-acting, double-rod ISO 15552 profile cylinder engineered for tasks demanding equal force and speed in both directions. Because a rod extends from both end covers, the annulus area is identical on the extend and retract sides, yielding a consistent 1402 N of thrust each way at 0.5 MPa. The extruded aluminum barrel features sensor grooves on both sides for flexible switch mounting.
This through-rod design allows you to mount the primary workpiece on the front rod while using the rear extension for a cam, position flag, or secondary mechanism. It utilizes a standard carbon steel rod and PT tapered port threads. The adjustable air cushions at both ends absorb kinetic energy near stroke limits, but note this cylinder does not hold position pneumatically if air pressure is lost.
| Model | Airtac SAID63 Double Rod Cylinder SAID63X180 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×180 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a shuttle mechanism where the 1402 N push and pull forces must be perfectly matched to prevent motor overload on the return stroke.
The dual-rod geometry keeps the guided load perfectly straight during the 180 mm travel, resisting torsional twist better than a single piston.
Mounts the primary tool on the front rod while the rear protrusion drives a secondary mechanical cam or limit flag for sequential timing.
Selecting this 63 mm bore over the smaller 50 mm variant steps the bidirectional force up from 825 N to 1402 N at 0.5 MPa, while stepping down from the 80 mm bore avoids the unnecessary bulk of its 2268 N output. The twin-rod architecture is chosen over a single-rod SAI when an application requires dual-side guidance to prevent rotation, or when a rear rod is needed to trigger a sensor. For direct compatibility, match the 63 mm bore, 180 mm stroke, PT port thread, and choose from the SAID mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), which omits the FB, CA, CB, and CR variants used only on single-rod models.
As this model lacks the -S magnet suffix, it cannot host AirTAC CMSE reed or DMSE electronic sensors without modification. If your workflow requires the piston to maintain its position during a loss of supply air, you must integrate an external pilot-operated check valve or transition to a locking variant like the BSAID.
AirtacDistr lists every SAID63 order code with its price on one page at https://airtacdistr.com/products/airtac-said63-double-rod-iso-cylinder
Quick checklist
Because the double-rod design occupies piston area on both sides, the extend and retract forces are equal. It provides 1402 N both ways at 0.5 MPa, 1962 N at 0.7 MPa, and 2523 N at 0.9 MPa.
Yes, it is dimensionally interchangeable with ISO 15552 profile cylinders. It supports a specific subset of mounts including Basic, FA, LB, TC, FTC, TCM1, and TCM2, but does not use the FB, CA, CB, or CR accessories found on single-rod versions.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.