verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SAI Series · ISO 15552 Cylinder

Airtac SAID63 Double Rod Cylinder SAID63X190S

The AirTAC SAID63 Double Rod Cylinder SAID63X190S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø63mm bore and 190mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke190 mm
  • Port sizeG3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$118.87 $126.37Save 5% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SAID63 stroke, mounting and version on one page All SAID63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SAID63 Double Rod Cylinder SAID63X190S

The AirTAC SAID63X190-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 63mm bore and 190mm stroke. Because a carbon steel rod exits both end covers, the annulus area is identical on both sides, yielding equal push and pull forces of 1402 N at 0.5 MPa. The integrated -S magnet enables position detection using CMSE reed or DMSE electronic sensors along the dual side grooves.

This through-rod design allows you to mount the primary workpiece on one end while attaching a cam, limit flag, or secondary mechanism to the rear rod. It provides superior anti-rotation guidance for symmetric loads compared to a single-rod SAI, while retaining the standard ISO 15552 mounting interface for direct interchangeability.

Airtac SAID63 Double Rod Cylinder SAID63X190S Technical Specifications

ModelAirtac SAID63 Double Rod Cylinder SAID63X190S
SeriesSAI ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke190 mm
Acting typeDouble acting
Port sizeG3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1402 N1402 N
0.7 MPa1962 N—
Max (@1.0 MPa)286 kgf

Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SAID63 Double Rod Cylinder SAID63X190S

SAIISO 15552 profile-barrel cylinder series.
63Bore size in mm.
×190Stroke length in mm.
-SOptional built-in magnet for sensor position sensing.

Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.

Where the Airtac SAID63 Double Rod Cylinder SAID63X190S Is Used

sync_alt

Symmetric Force Transfer

Drives payloads back and forth with identical 1402N force and velocity, preventing speed variations between extend and retract cycles.

straighten

Anti-Rotation Slides

Twin through-rods guide the load against torsional twist, maintaining strict parallelism for precision sliding fixtures.

settings_input_component

Rear-Side Sensing

Uses the rear protruding rod to trip external mechanical flags or drive secondary mechanisms while the front end executes the main task.

Is the Airtac SAID63 Double Rod Cylinder SAID63X190S the Right Cylinder?

Select this 63mm bore when an application demands perfectly symmetrical force and speed in both directions, offering 1402 N at 0.5 MPa. If your mechanism requires less force, stepping down to the 50mm bore provides 825 N both ways. For heavier payloads, the 80mm bore yields 2268 N. The 190mm stroke falls within the 1500mm standard maximum, making it a readily available configuration.

This model uses a PT tapered port thread and supports a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB, and CR brackets found on single-rod variants. Note that a plain SAID does not hold its position if air pressure is lost; for dead-end holding, consider the SAIL or BSAID clamp-lock series. Since the stroke is under 300mm, standard rod bearing bending is minimal, but external guides are recommended for high radial loads.

AirtacDistr lists every SAID63 order code with its price on one page at https://airtacdistr.com/products/airtac-said63-double-rod-iso-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/NPT/G)
  • ✓ Magnet (-S) for sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SAID63 Double Rod Cylinder SAID63X190S FAQ

Because the rod occupies both sides of the piston, the effective area is equal in both directions. It generates 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and 2523 N at 0.9 MPa on both extend and retract strokes.

Yes, the SAID63X190-S is dimensionally interchangeable per ISO 15552 profile cylinder standards. It serves as a direct replacement for other ISO 15552 double-rod cylinders, utilizing the same mounting interface and G3/8 port size.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SAI Cylinders

Request a Quote for Airtac SAID63 Double Rod Cylinder SAID63X190S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SAID63X190S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.