verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SAI Series · ISO 15552 Cylinder

Airtac SAID63 Double Rod Cylinder SAID63X425S

The AirTAC SAID63 Double Rod Cylinder SAID63X425S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø63mm bore and 425mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke425 mm
  • Port sizeG3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$149.78 $157.28Save 4% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SAID63 stroke, mounting and version on one page All SAID63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SAID63 Double Rod Cylinder SAID63X425S

The AirTAC SAID63X425-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 63mm bore and 425mm stroke. Because the twin rods occupy both sides of the piston, the annulus area is symmetrical, yielding an equal extend and retract force of 1402 N at 0.5 MPa. Supplied with a magnet, it integrates seamlessly with AirTAC CMSE reed and DMSE solid-state sensors mounted in the dual-side barrel grooves.

A defining advantage of this through-rod layout is the ability to mount the primary workpiece on the front end and a secondary cam, position flag, or guide on the rear rod end. The carbon steel rods enhance torsional stiffness and resist rotation better than a single-rod SAI, while the G3/8 porting supports a 30-800 mm/s speed range.

Airtac SAID63 Double Rod Cylinder SAID63X425S Technical Specifications

ModelAirtac SAID63 Double Rod Cylinder SAID63X425S
SeriesSAI ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke425 mm
Acting typeDouble acting
Port sizeG3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1402 N1402 N
0.7 MPa1962 N—
Max (@1.0 MPa)286 kgf

Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SAID63 Double Rod Cylinder SAID63X425S

SAIISO 15552 profile-barrel cylinder series.
63Bore size in mm.
×425Stroke length in mm.
-SOptional built-in magnet for sensor position sensing.

Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.

Where the Airtac SAID63 Double Rod Cylinder SAID63X425S Is Used

sync_alt

Symmetric Force Transfer

Ideal for pressing and transferring loads where the 1402 N force must be identical in both directions without speed variation.

straighten

Anti-Rotation Slides

The dual carbon steel rods provide superior torsional resistance, keeping the tool plate guided and preventing rotation over the 425mm stroke.

settings_input_component

Through-Rod Sensing

The rear rod end drives a secondary cam or flag, triggering CMSE or DMSE sensors for precise mid-stroke or end-of-stroke position feedback.

Is the Airtac SAID63 Double Rod Cylinder SAID63X425S the Right Cylinder?

Choose this 63mm bore when an application demands matched push and pull forces, or step down to the 50mm bore (825 N both ways at 0.5 MPa) for lighter loads. The twin-rod architecture is selected over a single-rod cylinder when dual-side guidance, anti-rotation control, or rear-rod position sensing is required. Mounting options are limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR brackets found on single-rod variants.

At 425mm, this stroke requires careful attention to side-load and rod-bearing bending. An external guide should be used to support the load and prevent premature seal wear. Note that a plain SAID does not hold its position if air pressure is lost; for locking needs, consider the SAIL or BSAID series. This cylinder is dimensionally interchangeable per ISO 15552 for direct replacement of other double-rod profile cylinders.

AirtacDistr lists every SAID63 order code with its price on one page at https://airtacdistr.com/products/airtac-said63-double-rod-iso-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/NPT/G)
  • ✓ Magnet (-S) for sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SAID63 Double Rod Cylinder SAID63X425S FAQ

Because it is a double-rod cylinder, the effective piston area is the same on both sides. It delivers an equal extend and retract force of 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and 2523 N at 0.9 MPa.

Yes, the SAID63X425-S shares the ISO 15552 mounting interface, making it dimensionally interchangeable with other standard double-rod profile cylinders. It uses a PT G3/8 port and supports AirTAC CMSE and DMSE sensors.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SAI Cylinders

Request a Quote for Airtac SAID63 Double Rod Cylinder SAID63X425S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SAID63X425S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.