
The AirTAC SAID63 Double Rod Cylinder SAID63X95S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø63mm bore and 95mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID63X95-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a built-in magnet for position sensing. Because the piston rod exits both end covers, the effective annulus area is identical on the extend and retract strokes. This provides an equal force of 1402 N in both directions at 0.5 MPa, ensuring perfectly symmetric motion dynamics.
A standard carbon steel rod drives the primary load, while the opposing rear rod end can simultaneously mount a cam, secondary tool, or a position flag for AirTAC CMSE reed or DMSE electronic sensors. The extruded aluminum barrel incorporates sensor grooves on both sides, and the unit uses adjustable air cushions at both ends to decelerate the piston smoothly.
| Model | Airtac SAID63 Double Rod Cylinder SAID63X95S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 95 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a workpiece clamp on the front rod while moving an opposing part on the rear rod, utilizing the identical 1402 N force for balanced dual-station actuation.
Guides heavy vertical loads with twin rod ends to prevent torsional twist, maintaining precise alignment without requiring external linear bearings.
Uses the -S magnet with DMSE electronic switches in the dual barrel grooves, while the protruding rear rod physically trips an external mechanical limit flag.
Select this 63 mm bore when an application requires 1402 N of symmetric push and pull force at 0.5 MPa, stepping up from the 50 mm bore which yields 825 N. A double-rod design is preferred over a single-rod SAI when the mechanism demands dual-side guidance, enhanced resistance to torsional rotation, or actuation on both ends of the machine. The PT port thread (G3/8) and standard 95 mm stroke make it a direct replacement for other ISO 15552 double-rod cylinders.
Ensure the mounting arrangement uses the SAID accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2), as FB, CA, CB, and CR variants are reserved for single-rod SAI units. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not lock or hold the load. If the system must maintain position upon loss of air pressure, specify a SAIL lock, BSAID clamp-lock, or an external pilot-operated check valve.
AirtacDistr lists every SAID63 order code with its price on one page at https://airtacdistr.com/products/airtac-said63-double-rod-iso-cylinder
Quick checklist
Because it is a double-rod cylinder, the push and pull forces are equal. It generates 1402 N in both directions at 0.5 MPa, 1962 N at 0.7 MPa, and 2523 N at 0.9 MPa.
Yes, it shares the exact ISO 15552 mounting interface dimensions and uses a G3/8 port, making it dimensionally interchangeable with other ISO 15552 profile cylinders. Just ensure your mounting accessories match the SAID supported set.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.