Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S
The AirTAC Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø80mm bore and 325mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke325 mm
- Port sizeG3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S
The AirTAC SAIJ80X325-30-S is a double-acting, single-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It delivers 2513N of push force at 0.5 MPa and features a 325mm nominal stroke that can be fine-tuned down by up to 30mm, creating a precise 295-325mm usable travel window. This built-in adjustability allows operators to dial in exact retract end positions during commissioning without swapping out the entire unit.
Fitted with a PT tapered port thread and a robust 25mm carbon steel rod with an M20x1.5 thread, this extruded aluminum barrel handles demanding cycles. The integrated -S magnet enables position detection via AirTAC CMSE reed or DMSE electronic solid-state sensors housed in the dual-side sensor grooves. Because the stroke exceeds 300mm, external guiding is recommended to manage side loads, and the rear stopper should never be mistaken for a lock, as it cannot hold a load without live air pressure.
Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S Technical Specifications
| Model | Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 325 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×325 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S Is Used
Product Changeover
Quickly adjust the retract distance from 325mm down to 295mm during packaging line size changes without replacing hardware.
Machine Setup
Fine-tune the exact end-stop position during initial commissioning to perfect material feeding and prevent mechanical crashes.
Variable End Stops
Accommodate multiple part lengths on a single conveyor system by rotating the rear adjuster screw to shift the stroke window.
Is the Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S the Right Cylinder?
Select this 80mm bore when an application requires substantial thrust, such as the 2513N push or 2268N pull at 0.5 MPa, but still needs on-the-fly end-position tuning. If your setup demands less force, stepping down to a 63mm bore yields 1559N push force, whereas moving up to a 100mm bore provides 3927N. The SAIJ series is chosen over a fixed-stroke SAI cylinder when product changeovers require variable end-stops, utilizing the rear screw to trim the 325mm stroke back to a 295mm minimum.
For a drop-in ISO 15552 replacement, match the 80mm bore, 325mm stroke, 30mm adjustment, PT port thread, and -S magnet. Mounting options are restricted to Basic, FA, LB, TC, FTC, TCM1, and TCM2, deliberately omitting FB, CA, CB, and CR brackets. Remember that the rear adjuster acts solely as a travel stop and deceleration point; for true load-holding without live air, utilize an external rod lock or explore the SAIL or BSAI cylinder variants.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S FAQ
At 0.5 MPa operating pressure, this 80mm bore cylinder provides 2513N of push force and 2268N of pull force. At the maximum 1.0 MPa pressure, it achieves a peak push force of 4523N.
The rear adjusting screw acts as a mechanical stopper that lets you shorten the 325mm nominal stroke by up to 30mm, providing a usable travel window of 295-325mm. This allows precise end-position tuning at commissioning without adding external stops, though it does not lock the load without live air.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAIJ80 Adjustable Cylinder SAIJ80X325-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.