Airtac SC100 Standard Cylinder SC100X1030S
The AirTAC Airtac SC100 Standard Cylinder SC100X1030S is a genuine double-acting standard air cylinder with a Ø100mm bore and 1030mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke1030 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X1030S
The AirTAC SC100X1030S is a double-acting tie-rod cylinder with a 100 mm bore and a non-standard 1030 mm stroke, factory-built with a built-in magnet for barrel-mounted sensors. At 0.5 MPa it delivers 3927 N push and 3681 N pull, scaling to 7068 N at the 0.9 MPa maximum operating pressure.
This model uses a 25 mm diameter piston rod with M20x1.5 male threads and PT1/2 ports. The adjustable air cushion (29 mm length) decelerates the piston near end-of-stroke, and the total extended body length is approximately 1291 mm. The built-in magnet allows direct clamping of CMSG/DMSG/EMSG reed or solid-state sensors for position feedback without extra brackets.
Airtac SC100 Standard Cylinder SC100X1030S Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X1030S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 1030 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X1030S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×1030 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X1030S Is Used
Long-Reach Material Transfer
The 1030 mm stroke pushes or pulls bins, pallets, or workpieces across wide conveyor gaps, with the magnet enabling end-of-stroke confirmation for automated sequencing.
Large Panel Pressing
Delivers up to 7068 N at 0.9 MPa to clamp or form large panels, with adjustable cushioning softening the stop on this long-travel tooling stroke.
Automated Diverter Gates
Operates high-reach diverter gates in bulk handling lines; the built-in magnet lets sensors verify gate open/closed position for interlock safety.
Is the Airtac SC100 Standard Cylinder SC100X1030S the Right Cylinder?
Choose the SC100 bore when your application needs roughly 4000 N of push at standard plant pressure; stepping down to the SC80 bore provides about 2513 N at the same 0.5 MPa, while stepping up to the SC125 bore jumps to 6136 N. This 1030 mm stroke exceeds the standard 1500 mm maximum for the 100 mm bore, so it is a made-to-order non-standard stroke—confirm lead time with your AirTAC distributor.
For a 1030 mm stroke, the 25 mm rod is relatively slender. Any side load, even a small misalignment, can cause rod bending or accelerated bearing wear. Use an external guide rail, rod-alignment coupler, or a guided cylinder assembly to protect the rod and bearing. When replacing an existing cylinder, match five points: 100 mm bore, 1030 mm stroke, PT1/2 port thread, the built-in magnet (-S), and the basic (no bracket) mounting configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X1030S FAQ
At 0.5 MPa the cylinder produces 3927 N extending and 3681 N retracting. At the maximum operating pressure of 0.9 MPa, the push force reaches 7068 N. The theoretical force at 1.0 MPa is 801 kgf, but the cylinder is rated only to 1.0 MPa operating pressure.
Yes. The -S suffix means a magnet is built into the piston, so CMSG, DMSG, or EMSG reed and solid-state sensors can be clamped directly onto the tie-rod barrel to detect piston position. No external brackets or modifications are needed.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X1030S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.