Airtac SC100 Standard Cylinder SC100X365STC
The AirTAC Airtac SC100 Standard Cylinder SC100X365STC is a genuine double-acting standard air cylinder with a Ø100mm bore and 365mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke365 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X365STC
The AirTAC SC100X365STC is a double-acting single-rod pneumatic cylinder delivering 3927 N of push force at 0.5 MPa (7068 N at 0.9 MPa). Its 100 mm bore and 365 mm stroke suit medium-to-heavy linear actuation tasks where a pivoting mount is required.
This model includes a built-in magnet (-S) for direct mounting of CMSG/DMSG/EMSG sensors, and the TC centre trunnion mount (supplied with TCM1 bracket, part F-SC100TC) allows the cylinder to swing through an arc. The 25 mm diameter rod and 29 mm adjustable air cushion provide smooth deceleration. Body length A is 188 mm; total extended length is approximately 553 mm.
Airtac SC100 Standard Cylinder SC100X365STC Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X365STC |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 365 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X365STC
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×365 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X365STC Is Used
Conveyor Diverter Gates
The 365 mm stroke and 3927 N push force at 0.5 MPa reliably actuate heavy diverter gates in material handling lines. The TC trunnion mount allows the cylinder to pivot as the gate swings.
Clamping & Welding Fixtures
Delivers 7068 N of clamping force at 0.9 MPa for holding large weldments or castings. The built-in magnet enables end-of-stroke confirmation via CMSG sensors for automated cycle start.
Agricultural Equipment Actuation
Suited for pivoting chute controls or bin gate operation on harvesters and planters. The TPU seals and PT ports handle typical farm air supply conditions within the -20 to +70 C range.
Is the Airtac SC100 Standard Cylinder SC100X365STC the Right Cylinder?
Choose the SC100 bore when your application needs around 4000 N of force at standard plant pressure. If the load is lighter, stepping down to an SC80 (2513 N push at 0.5 MPa) can reduce air consumption and physical size. For higher force, the SC125 bore provides 6136 N at 0.5 MPa.
This 365 mm stroke is within the 1500 mm standard maximum for the 100 mm bore. For strokes over 300 mm, always check side-load conditions—a long, unsupported 25 mm rod can bend under lateral force. Use an external guide rail or a guided cylinder if the load is not perfectly axial. For a direct replacement, match these five points: 100 mm bore, 365 mm stroke, PT port thread, TC centre trunnion mount, and the -S magnet for sensor compatibility.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X365STC FAQ
At 0.5 MPa, push force is 3927 N and pull force is 3681 N. At the maximum operating pressure of 0.9 MPa, push force reaches 7068 N. The theoretical maximum at 1.0 MPa is 801 kgf.
No. The SC100 is a double-acting cylinder and will drift or drop if air pressure is lost or the directional valve is centered. To hold a load safely without live pressure, you must add an external rod lock, a pilot-operated check valve, or a mechanical brake.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X365STC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.