Airtac SC100 Standard Cylinder SC100X415S
The AirTAC Airtac SC100 Standard Cylinder SC100X415S is a genuine double-acting standard air cylinder with a Ø100mm bore and 415mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke415 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X415S
The AirTAC SC100X415S is a double-acting tie-rod cylinder delivering 3927 N of push force at 0.5 MPa and up to 7068 N at 0.9 MPa operating pressure. Its 100 mm bore, 25 mm diameter piston rod, and 415 mm stroke suit medium-to-heavy linear actuation tasks where a compact tie-rod design is preferred. The -S suffix denotes a factory-installed magnet, enabling direct mounting of CMSG, DMSG, or EMSG reed and solid-state sensors on the barrel for contactless position feedback.
With a body length A of 188 mm and an adjustable air cushion of 29 mm, this cylinder decelerates the piston smoothly at stroke end to reduce impact. The PT1/2 port and M20x1.5 rod thread are standard for this bore class. Operating on filtered air from 0.15 to 1.0 MPa and rated for -20 to +70 °C with TPU/NBR seals, the SC100X415S is a genuine AirTAC actuator built for consistent performance in industrial automation.
Airtac SC100 Standard Cylinder SC100X415S Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X415S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 415 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X415S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×415 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X415S Is Used
Conveyor Divert & Stop
The 415 mm stroke and 3927 N push force at 0.5 MPa handle pallet stops and diverter gates on medium-duty conveyor lines. The built-in magnet allows end-of-stroke sensing for precise timing.
Press & Clamp Fixtures
With 7068 N of force at 0.9 MPa, this cylinder powers holding clamps and light press-fit tooling. The adjustable cushion protects the fixture from impact at the end of the 415 mm stroke.
Lift & Tilt Tables
Use the SC100X415S on scissor lifts or tilt mechanisms where the 415 mm stroke provides the required range of motion. The magnetic piston enables sensor-based height or angle confirmation.
Is the Airtac SC100 Standard Cylinder SC100X415S the Right Cylinder?
This 100 mm bore cylinder provides 3927 N at 0.5 MPa. If your load demands more force, step up to the SC125 series (6136 N at 0.5 MPa); for a lighter, more compact solution, the SC80 (2513 N at 0.5 MPa) may suffice. The 415 mm stroke is within the 1500 mm maximum standard stroke for this bore. For strokes of this length, avoid unsupported side loads—the 25 mm rod can bend under lateral force; use an external linear guide or a guided cylinder if off-axis loading is present.
To replace an existing unit, match five points exactly: 100 mm bore, 415 mm stroke, PT1/2 port thread, the built-in magnet (-S suffix), and the basic (no bracket) mounting. The SC is a tie-rod cylinder, not an ISO 15552 profile cylinder, so dimensional interchangeability is limited to other AirTAC SC tie-rod cylinders of the same configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X415S FAQ
At 0.5 MPa air pressure, the cylinder pushes with 3927 N and pulls with 3681 N. At the maximum operating pressure of 0.9 MPa, the push force increases to 7068 N. The theoretical maximum force at 1.0 MPa is 801 kgf.
No. The SC series is a tie-rod cylinder and is physically shorter than an ISO 15552 profile cylinder, so it is not dimensionally interchangeable. It directly replaces another AirTAC SC100 tie-rod cylinder with the same 415 mm stroke, PT1/2 ports, and -S magnet option.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X415S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.