The AirTAC AirTAC SDA80X10H Compact Cylinder | 80mm Bore FKM is a genuine double-acting COMPACT (thin) air cylinder with a Ø80mm bore and 10mm stroke, PT3/8 air ports and a riveted short body that saves mounting depth. Sensor slots around the body accept magnetic switches for position sensing.
The AirTAC SDA80X10H is a double-acting single-rod compact cylinder engineered for high-force tasks in confined footprints. Its short riveted body drastically reduces axial mounting depth compared to round-body units, yielding a substantial 2513.3 N push at 0.5 MPa. This specific SKU incorporates fluororubber (FKM) seals for enhanced thermal and oil resistance, operating within the standard -20 to +70 C range.
Built with a hard-anodized 80mm bore and a robust 25mm piston rod, it handles a safe working load of roughly 1508 N (about 60% of the 0.5 MPa rating). End-of-travel deceleration relies on a fixed NBR bumper rather than an adjustable air cushion. Note that this base configuration lacks a piston magnet, so position sensing is unavailable without the -S variant.
| Model | AirTAC SDA80X10H Compact Cylinder | 80mm Bore FKM |
|---|---|
| Series | SDA compact (thin) cylinder |
| Bore size | Ø80 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M14×1.5 female / M22×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 120 mm |
Specifications follow the official AirTAC SDA compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard). Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SDA | Compact (thin) double-acting cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard. Related SDA-family variants: SSA (single-acting push), STA (single-acting pull), SDAD (double rod), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Provides intense short-stroke ejection force for heavy plastic injection molds where axial depth is severely restricted by the machine platen.
Acts as a high-power clamping or positioning stop in automated metal stamping lines, utilizing its 2513.3 N capability to secure heavy coil stock.
Functions as a robust mechanical stop in end-of-line palletizing systems, enduring high kinetic impacts with the help of external shock absorbers.
When sizing this actuator, stepping down to the SDA63 yields 1558.6 N of push at 0.5 MPa, while stepping up to the SDA100 provides 3927 N. The SDA80X10H sits in this heavy-duty middle ground, delivering a theoretical maximum output of 513 kgf at 1.0 MPa. To verify your ordering essentials: specify the 80mm bore, 10mm stroke, PT3/8 port thread, female M14x1.5 rod end, and the FKM seal option.
Remember that a standard compact cylinder cannot hold a load if air pressure drops or the valve is centered; the piston will drift, and the fixed bumper only decelerates near the stroke end. If your application demands vertical position holding—such as a 128.1 kg lift with a 2:1 safety margin—you must integrate an external rod lock or a pilot-operated check valve.
Quick checklist
This 80mm bore double-acting cylinder generates 2513.3 N push and 2267.8 N pull at 0.5 MPa, and 3518.6 N push at 0.7 MPa. Its theoretical maximum push is 513 kgf at 1.0 MPa, with a proof pressure of 1.5 MPa.
No. This specific SKU lacks the -S magnet, so it cannot accept reed or electronic switches. Additionally, it uses a fixed NBR bumper for end-of-stroke deceleration, not an adjustable air cushion; high-speed applications require external shock absorption.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.