
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X35-30SB is a genuine double-acting COMPACT cylinder (Ø12mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 5 to 35 mm on the machine — no shims, no part change.
The AirTAC SDAJ12X35-30SB is a compact double-acting double-rod cylinder featuring an on-site adjustable extend stop. An M5x0.8 adjuster screw lets you dial the outward stroke anywhere between 5 and 35 mm without changing parts.
This variant includes a built-in piston magnet for AirTAC reed or electronic switches and a male M5x0.8 piston rod end. The short riveted body saves valuable axial mounting depth where larger profile cylinders cannot fit. End-of-travel deceleration is handled by a fixed NBR bumper, which slows the stroke but does not function as an adjustable air cushion or a load lock.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X35-30SB |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø12 mm |
| Max stroke | 35 mm |
| Adjustable range | 5 – 35 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 42 N | 42 N |
| 0.7 MPa | 59 N | — |
| Max (@1.0 MPa) | 9 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 12 | Bore size in mm. |
| ×35 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Perfect for small machining fixtures where the male M5 rod advances a clamp. The M5 adjuster screw lets operators fine-tune the 5-35 mm extend stop on the machine to accommodate varying part tolerances without swapping shims.
Ideal for testing rigs needing exact probe contact.
Fits into tight electronics assembly modules where axial depth is restricted. The short riveted body and 30 mm adjustment window allow technicians to set the exact ejection distance on-site during initial line commissioning.
When sizing this 12 mm bore actuator, consider your force margins carefully. Dropping down is not an option as this is the smallest available SDAJ bore, but stepping up to the 16 mm bore raises the 0.5 MPa push output to 100.5 N. If your application requires on-site stroke tuning to dial in a precise end position, the 30 mm adjustment window is highly effective.
Confirm your parameters before ordering: 12 mm bore, 35 mm maximum stroke, 30 mm adjust window, M5x0.8 air port, male M5x0.8 rod thread, and a built-in magnet. Remember that a plain compact cylinder does not hold its load if air pressure drops or the valve is centered—the piston will drift. For suspended or vertical loads that must remain fixed without live pressure, specify an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, the push force is 79.2 N. The theoretical maximum push force is 12 kgf at 1.0 MPa.
The M5x0.8 adjuster screw mechanically shortens the extend stroke by up to 30 mm, allowing an adjustable range of 5 to 35 mm. The included -S magnet enables position sensing with AirTAC reed or solid-state electronic switches mounted in the body grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.