
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X65-40B is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 25 to 65 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X65-40B is a compact double-acting double-rod cylinder featuring an on-site adjustable extend stop. An external M6x1.0 adjuster screw lets you dial the outward stroke anywhere from 25 to 65 mm, eliminating the need for shims or part swaps during machine commissioning.
This thin riveted-body design saves valuable axial mounting depth where larger profile cylinders cannot fit. The unit features an 8 mm piston rod with a male M6x1.0 thread end, operating at speeds between 30 and 500 mm/s. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion, and this specific SKU lacks a piston magnet, so it cannot support magnetic sensing.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X65-40B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 65 mm |
| Adjustable range | 25 – 65 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×65 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Tune the stroke length on-site to accommodate varying package sizes on a belt line, using the fixed NBR bumper to absorb the deceleration of each cycle.
Iterate rapidly on trial assemblies by adjusting the outward reach in millimeters, leveraging the 8 mm male M6 rod end for easy custom tooling attachment.
When sizing this 20 mm bore actuator, evaluate your force requirements both ways. Choose this specific model if your fixture setup demands frequent trial positioning or changeover, utilizing the 40 mm adjustment window to fine-tune the extend endpoint precisely on the machine.
Confirm your parameters before ordering: a 20 mm bore, 65 mm maximum stroke, and a 40 mm adjustable window. The air port is M5x0.8, and the rod end utilizes the male M6x1.0 thread (-B option). Note that this configuration has no piston magnet (-S omitted), meaning reed or electronic switches cannot be used. Also, a standard compact cylinder does not hold position upon air loss or valve centering; the fixed bumper only decelerates the stroke end rather than locking the load. For secure load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, the push increases to 219.9 N. The theoretical maximum push force is 32 kgf at 1.0 MPa.
Turning the external R (M6x1.0) screw shortens the extend stroke by up to 40 mm, allowing the rod to stop anywhere between 25 and 65 mm. This specific SKU lacks the -S magnet option, so it cannot accept AirTAC reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.