
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X110-100B is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 10 to 110 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X110-100B is a compact double-acting double-rod cylinder featuring an external M8x1.25 adjustment screw. This mechanism lets you dial the extend stop anywhere between 10 and 110 mm directly on your machine, eliminating the need for shims or part swaps.
Designed with a short riveted body, this unit saves axial mounting depth where round-body or profile cylinders will not fit. It includes a male M8x1.25 piston rod thread and relies on a fixed NBR bumper at each end to decelerate the stroke. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic switches.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X110-100B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 110 mm |
| Adjustable range | 10 – 110 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 100 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -100 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 10 to 110 mm extend stop during prototype runs.
Swap product families and rotate the M8x1.25 adjuster screw to match new part heights instantly, avoiding the downtime of physically replacing cylinders.
Set a precise mechanical lower limit for 12.5 kg vertical lifts. The fixed NBR bumper absorbs the end shock without requiring complex cushion valves.
Stepping down to the SDAJ20 yields 157.1 N, while moving up to the SDAJ32 provides 402.1 N. Choose this specific unit if your fixture requires a male M8x1.25 rod end and extensive on-site stroke tuning across a 100 mm window.
Confirm your requirements for the M5x0.8 air port and the absence of a magnet. A plain cylinder does not hold its load when air is lost or the valve is centered; the piston drifts, and the fixed bumper only decelerates near the end of travel. For secure load holding without live pressure, you must integrate an external rod lock or a pilot-operated check valve.
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa, proof pressure is 1.5 MPa, and speed ranges from 30-500 mm/s.
Turning the external R (M8x1.25) screw shortens the extend stroke by up to 100 mm, giving a usable range of 10-110 mm. The screw sets the stop position and does not alter force. This SKU has no piston magnet, so it cannot take a switch; you must select the -S variant to use reed or electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.