
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X70-20 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 50 to 70 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X70-20 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M8x1.25) screw, you can dial the forward stroke down by up to 20 mm directly on your machine, yielding a usable extend range of 50 to 70 mm without swapping shims or parts.
This thin riveted body drastically cuts axial mounting depth where larger profile or round-body units fail to fit. End-of-travel deceleration relies on a fixed NBR bumper rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches; order the -S variant if sensing is required.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X70-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 70 mm |
| Adjustable range | 50 – 70 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×70 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the 50-70 mm extend position during machine setup to accommodate different part heights without machining new spacers.
Fine-tune the extend endpoint in 20 mm increments to find the exact contact point for delicate forming tasks before locking the screw.
Choose this model if your fixture requires on-site stroke tuning during frequent changeovers.
Confirm your parameters: 25 mm bore, 70 mm maximum stroke, 20 mm adjust window, and an M5x0.8 port. This base configuration uses a female M5x0.8 rod-end thread and includes no magnet. Remember that a plain cylinder drifts when air is lost or the valve centres—the fixed bumper only decelerates near the end and acts as a mechanical stop, not a lock. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa.
The R (M8x1.25) screw mechanically shortens the extend stop by up to 20 mm, giving a 50-70 mm range; it does not alter force. This specific SKU lacks a piston magnet, so it cannot take a switch; you need the -S option for reed or electronic sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.