
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X70-30 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 40 to 70 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X70-30 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M8x1.25 adjuster screw lets you dial the outward stroke down by up to 30 mm on the machine, yielding a usable extend range of 40 to 70 mm without swapping shims or parts. Retract remains at the full 70 mm.
The short riveted body saves axial mounting depth where a round-body or profile cylinder will not fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. This specific SKU lacks a piston magnet, so it cannot accept reed or electronic switches; you would need the -S variant for position sensing. Operating speed spans 30 to 500 mm/s.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X70-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 70 mm |
| Adjustable range | 40 – 70 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×70 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 40 and 70 mm to set precise insertion depths for varying panel thicknesses without reprogramming the motion controller.
Stepping down, the SDAJ20 delivers 157.1 N, which may be insufficient for heavier fixtures; stepping up, the SDAJ32 provides 402.1 N for high-friction slides.
This model is tailored for operators needing on-machine stroke tuning during frequent format changeovers. Confirm your requirements for a 25 mm bore, 70 mm maximum stroke, 30 mm adjust window, M5x0.8 port, female rod-end thread, and no magnet. Note that a plain SDAJ does not hold position or load when air is lost or the valve is centred; the fixed bumper only decelerates near the end. For load holding without live pressure, integrate an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push force is 50 kgf at 1.0 MPa. The M8x1.25 adjuster screw changes the stop position only, leaving these force values identical to a standard SDA of the same bore.
Turning the external R screw shortens the extend stroke by up to 30 mm, allowing you to set the outward end position anywhere between 40 and 70 mm. This screw acts purely as a mechanical stop and does not function as a mid-stroke lock. If you need to hold a load vertically during air loss, you must add an external rod lock or pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.