
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X140-30B is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 110 to 140 mm on the machine — no shims, no part change.
The SDAJ32X140-30B is a compact double-acting double-rod cylinder featuring an external M10x1.25 adjuster screw that dials the extend stop on-site between 110 and 140 mm. This specific 140 mm unit is a non-standard made-to-order length, exceeding the 130 mm maximum standard stroke for a 32 mm bore.
Built with a short riveted body, it saves axial mounting depth where round-body or profile cylinders cannot fit. The unit includes a male M10x1.25 piston rod thread (option B) and relies on a fixed NBR bumper at each end to decelerate the stroke end. This SKU lacks a piston magnet, so it cannot support magnetic sensing; adding the -S option enables reed or electronic switches.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X140-30B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 140 mm |
| Adjustable range | 110 – 140 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×140 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 110 to 140 mm during tooling changeovers to position parts accurately without fabricating new shims.
Fine-tune the end position during trial setups to find the exact 20.5 kg vertical contact point before finalizing a fixture.
Choose this adjustable-stop model if your application requires frequent on-machine stroke tuning between 110 and 140 mm. Remember that a plain cylinder does not hold its load on air loss or when the valve is centered; the piston drifts, and the fixed NBR bumper only decelerates near the end of travel. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve. Confirm your required 140 mm length, 30 mm window, PT1/8 port, male M10x1.25 rod, and lack of magnet before ordering.
Quick checklist
At 0.7 MPa the push is 563 N and pull is 483.8 N. The theoretical maximum push is 82 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa, proof pressure is 1.5 MPa, and the speed range is 30-500 mm/s.
Turning the R (M10x1.25) external screw shortens the extend stroke by up to 30 mm, allowing an on-machine range of 110 to 140 mm. This sets a mechanical stop and does not change the force. It is not a mid-stroke lock; the piston drifts on air loss, so use an external rod lock for load holding. This SKU has no magnet, but the -S variant adds one for reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.