
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X100-30S is a genuine double-acting COMPACT cylinder (Ø40mm bore) whose extend end-position is set by an external M12×1.25 adjustment screw. You can dial the stroke anywhere from 70 to 100 mm on the machine — no shims, no part change.
The AirTAC SDAJ40X100-30S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M12x1.25 adjuster screw lets you dial the forward end-position anywhere between 70 and 100 mm directly on the machine, eliminating the need for shims or part swaps during changeovers. Retract remains at the full stroke length.
The short riveted body saves valuable axial mounting depth where round-body or profile cylinders cannot fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X100-30S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Max stroke | 100 mm |
| Adjustable range | 70 – 100 mm |
| Adjuster thread (R) | M12×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M8×1.25 F / M14×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the M12x1.25 screw to position the clamp between 70 and 100 mm, accommodating raw material thickness variations without swapping actuators on the fixture.
Set a repeatable metal bending edge anywhere in the 30 mm window. The fixed NBR bumper absorbs the end shock, protecting the 16 mm rod from sudden impact loads.
Choose this specific model if your fixture setup requires frequent trial positioning or on-machine stroke tuning.
Confirm the bore 40, stroke 100, and 30 mm adjustment window fit your spatial envelope, noting the PT1/8 port and 16 mm rod diameter. This variant includes the S option for a built-in magnet compatible with AirTAC reed or electronic switches. Remember that a plain cylinder does not hold its load on air loss or when the valve is centered; the piston drifts. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
The theoretical maximum push is 128 kgf at 1.0 MPa. It operates between 0.15 and 1.0 MPa, with a proof pressure of 1.5 MPa, and runs at speeds from 30 to 500 mm/s.
The external M12x1.25 screw mechanically shortens the extend stroke by up to 30 mm, giving a usable forward range of 70 to 100 mm. It sets the stop position and does not alter the output force. The built-in S magnet is solely for positioning detection via AirTAC reed or electronic switches and does not influence the mechanical stop.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.