
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X100-10 is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 90 to 100 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X100-10 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the M16x1.5 adjuster screw, you can dial the forward stroke down by 10 mm on the machine, yielding a usable extend range of 90 to 100 mm without swapping shims or parts.
This 63 mm bore unit relies on a fixed NBR bumper at each end to decelerate the stroke, which is not an adjustable air cushion or a mid-stroke lock. The short riveted body saves axial mounting depth where round-body or profile cylinders will not fit. Operating pressure spans 0.15 to 1.0 MPa, and the piston speed ranges from 30 to 500 mm/s.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X100-10 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 100 mm |
| Adjustable range | 90 – 100 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Turn the M16x1.5 screw to fine-tune the 90-100 mm extend stop during press-fit setups, ensuring delicate components seat perfectly without re-machining hard stops.
Choose this specific SKU if your fixture requires on-site extend tuning between 90 and 100 mm. Confirm your parameters: 63 mm bore, 100 mm max stroke, 10 mm window, PT1/4 port, female M10x1.5 rod-end thread, and no magnet. Because this variant lacks the -S magnet, it cannot accept reed or electronic switches. Note that a plain cylinder does not hold its load on air loss or valve centring; the piston drifts and the bumper only decelerates near the end. For a held load, specify an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 2182.1 N and pull to 1962.2 N. The theoretical maximum push is 318 kgf at 1.0 MPa.
The external M16x1.5 screw shortens the extend stop by up to 10 mm, allowing you to set the forward stroke anywhere between 90 and 100 mm. It acts purely as a mechanical stop and does not alter force. The cylinder cannot hold a load if air is lost; use an external rod lock or pilot-operated check valve for load holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.