
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X110-50B is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 60 to 110 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X110-50B is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M16x1.5) screw, you can dial the forward stroke down from its 110 mm maximum to a 60 mm minimum directly on the machine, avoiding any part changes.
This variant features a male M18x1.5 threaded piston rod (Ø20 mm) for secure tool mounting and uses a PT1/4 air port. The short riveted body saves axial mounting depth where a larger profile cylinder will not fit. End-of-travel deceleration is handled by a fixed NBR bumper, which is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet and cannot support sensing.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X110-50B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 110 mm |
| Adjustable range | 60 – 110 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adjust the extend position on the fly to deflect different carton sizes on a packaging line, using the 50 mm window to fine-tune the push distance.
Safely lower a 79.4 kg tooling head during setup by limiting the downward stroke, preventing hard crashes before finalizing the mechanical stop.
Choose the 63 mm bore when the 50 mm falls short on thrust but you want to avoid the bulk of an 80 mm body.
This model is ideal for operators needing frequent on-machine stroke tuning between 60 and 110 mm during product changeovers. Confirm your requirements for the 63 mm bore, 110 mm maximum stroke, 50 mm window, PT1/4 port, male M18x1.5 rod (-B), and the absence of a magnet. Remember that a plain cylinder does not hold a load on air loss or valve centering; the bumper only decelerates near the end. For suspended loads, install an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 2182.1 N. The theoretical maximum push is 318 kgf at 1.0 MPa.
Turning the external R (M16x1.5) screw shortens the extend end position from the 110 mm maximum down to 60 mm. This SKU lacks a piston magnet, so it cannot take a magnetic switch; you would need the -S variant for reed or electronic sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.