
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X80-75B is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 5 to 80 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X80-75B is a double-acting compact cylinder featuring a male-thread M18x1.5 piston rod and an external R (M16x1.5) adjuster screw. Turning this screw lets you dial the extend stop down from the 80mm maximum to a 5mm minimum directly on the machine, yielding a 75mm adjustable window without swapping shims or parts.
The short riveted body conserves axial mounting depth where a longer round-body or profile cylinder would fail to fit. End-of-stroke deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion, and this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches. Note that the bumper and adjuster only manage the end position; they do not lock the rod, so a separate rod lock or pilot-operated check valve is required to hold a load safely during air loss.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X80-75B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 80 mm |
| Adjustable range | 5 – 80 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 75 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×80 | Maximum stroke length in mm. |
| -75 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Use the M16x1.5 adjuster screw to set precise folding depths on the fly for different box sizes, relying on the male M18x1.5 rod thread to secure heavy forming tooling securely.
Choose this specific configuration if your fixture requires a male M18x1.5 rod end and frequent on-site stroke tuning across the 5-80mm range.
Confirm your requirements against these exact specs: 63mm bore, 80mm max stroke, 75mm adjust window, PT1/4 air port, and no magnet (non-S variant). Remember that a standard double-acting cylinder drifts when valve pressure is centred or lost, so never rely on the fixed bumper or the R screw as a braking mechanism for suspended loads. If your cycle speeds exceed the 30-500mm/s range and generate high kinetic energy, consider adding an external shock absorber to protect the NBR bumper.
Quick checklist
The theoretical maximum push is 318kgf at 1.0MPa. Operating pressure is 0.15-1.0MPa, proof pressure is 1.5MPa, and speed ranges from 30-500mm/s.
The R (M16x1.5) screw mechanically shortens the extend stroke by up to 75mm, allowing the rod to stop anywhere between 5mm and 80mm; retract remains full and force is unchanged. This specific SKU lacks a piston magnet, so it cannot accept reed or electronic switches—you must select an -S variant for position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.