Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30
The AirTAC Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30 is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 80 to 110 mm on the machine — no shims, no part change.
- BoreØ100 mm
- Max stroke110 mm
- Adjustable range80–110 mm
- Adjuster threadM27×2.0
- Port sizePT3/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30
The AirTAC SDAJ100X110-30 is a double-acting compact cylinder featuring an external adjustable extend stop. By turning the R (M27x2.0) screw, you dial the forward end-position anywhere between 80 and 110 mm directly on your machine, eliminating shims or part swaps. The mechanism sets the mechanical stop without altering the piston area, delivering full standard SDA force of 3927 N push at 0.5 MPa.
Its short riveted body drastically saves axial mounting depth where a larger profile cylinder cannot fit. End-of-stroke energy is managed by a fixed NBR bumper that decelerates the load, rather than an adjustable air cushion. This specific SKU lacks a piston magnet, so it cannot host reed or electronic switches.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30 Technical Specifications
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 110 mm |
| Adjustable range | 80 – 110 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. Force is unchanged from a standard SDA of the same bore. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Force matches a standard SDA of the same bore; the adjuster only sets the stop position, not the area. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30 Is Used
Heavy Press Tuning
Dial the 80-110 mm extend stop precisely during press changeovers to accommodate varying workpiece heights without swapping mechanical spacers.
Vertical Lifting Jig
Lift loads up to 200.2 kg safely using the 2:1 margin, adjusting the downward travel limit via the M27x2.0 screw to prevent over-travel.
Compact Clamping Station
Utilize the short riveted body to save axial depth in tight cells while delivering 3927 N of clamping force at 0.5 MPa.
Is the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30 the Right Cylinder?
When sizing this unit, look both ways: stepping down to an SDAJ80 yields 2513.3 N push at 0.5 MPa, while this 100 mm bore provides 3927 N. A practical safe working load is roughly 2356 N (about 60 percent of the 0.5 MPa figure), translating to a vertical lift capacity near 200.2 kg with a 2:1 safety margin. Choose this model if your assembly requires heavy push force plus on-site stroke tuning during commissioning.
Confirm your parameters: 100 mm bore, 110 mm max stroke, 30 mm adjust window, and a PT3/8 air port. The rod end features a female M18x1.5 thread. Remember that a plain cylinder does not hold position on air loss or valve centring; the fixed bumper only decelerates near the end and is never a lock. For secure load holding without live pressure, install an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 80–110 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M27×2.0 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30 FAQ
This 100 mm bore cylinder delivers 3927 N push and 3524.9 N pull at 0.5 MPa. At 0.7 MPa, push is 5497.8 N and pull is 4934.8 N. The theoretical maximum push is 801 kgf at 1.0 MPa.
The external M27x2.0 adjuster screw shortens the extend stroke by up to 30 mm, giving a usable forward range of 80 to 110 mm. It acts strictly as a mechanical stop and does not alter force. This SKU has no magnet (-S), so it cannot support sensing switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.