
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X75-50S is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 25 to 75 mm on the machine — no shims, no part change.
The SDAJ100X75-50S is a double-acting compact cylinder featuring a 100 mm bore and a built-in piston magnet. An external M27x2.0 adjuster screw lets you dial the extend stop down from 75 mm to 25 mm directly on the machine, eliminating the need for shims or part swaps during changeovers.
This riveted-body design saves substantial axial mounting depth compared to conventional round-body units, fitting into tight footprints while managing high energy. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. The integrated magnet supports AirTAC reed or electronic switches for precise end-position sensing.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X75-50S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 75 mm |
| Adjustable range | 25 – 75 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | — |
| Max (@1.0 MPa) | 719 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×75 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the 25-75 mm extend stop on heavy press lines to accommodate varying material thicknesses without swapping out actuators.
Rapidly reconfigure end-of-arm tooling depth on packaging lines by turning the adjuster screw to match new container heights on the fly.
This model is ideal for setups requiring frequent on-site stroke tuning between 25 mm and 75 mm without replacing hardware. Confirm your setup needs a PT3/8 air port, a female M18x1.5 rod-end thread, and the -S magnet option for switch sensing. Remember that a plain cylinder does not hold its load on air loss or when the valve is centred; the fixed bumper only decelerates near the end of the stroke. For load holding without live pressure, you must integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj100-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 5497.8 N and pull to 4934.8 N. The theoretical maximum push force is 801 kgf at 1.0 MPa.
The M27x2.0 adjuster screw mechanically shortens the extend stroke window from 75 mm down to 25 mm without changing the output force. The included -S magnet allows you to mount AirTAC reed or electronic solid-state switches directly into the body sensor grooves for position feedback.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.