Airtac SE100 Standard Air Cylinder SE100AX160S
The AirTAC Airtac SE100 Standard Air Cylinder SE100AX160S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 160mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke160 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE100 Standard Air Cylinder SE100AX160S
The AirTAC SE100AX160S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It delivers a robust 3927 N push force at 0.5 MPa, scaling to 5497 N at 0.7 MPa. Equipped with a SUS420J2 stainless steel rod (code A), this 100mm bore unit is purpose-built for corrosive and washdown environments where standard carbon steel rods would fail.
The extruded aluminum barrel eliminates external tie rods, yielding a compact, flush-mounting profile that resists corrosion and simplifies fixture integration. An integrated magnet (code S) enables seamless position feedback via CMSE reed or DMSE electronic sensors. Field-adjustable pneumatic cushioning at both ends allows precise tuning of end-of-stroke deceleration to absorb high kinetic energy from heavy 801 kgf maximum loads.
Airtac SE100 Standard Air Cylinder SE100AX160S Technical Specifications
| Model | Airtac SE100 Standard Air Cylinder SE100AX160S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 160 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE100 Standard Air Cylinder SE100AX160S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE100 Standard Air Cylinder SE100AX160S Is Used
Palletizer Case Pusher
Drives heavy corrugated cartons onto pallets in washdown packaging lines, utilizing the 3927 N push force and SUS420J2 stainless rod to resist moisture and cleaning chemicals.
CNC Fixture Clamp
Secures large aluminum engine blocks during high-speed machining, relying on the 100mm bore's 5497 N push at 0.7 MPa and the adjustable cushion to prevent hard end-stop impact.
Food Processing Diverter
Actuates sorting gates for bulk ingredient routing, using the integrated -S magnet with DMSE electronic sensors for precise position verification in hygienic environments.
Is the Airtac SE100 Standard Air Cylinder SE100AX160S the Right Cylinder?
This 100mm bore cylinder provides 3927 N of push force at 0.5 MPa. If your application requires less force, the adjacent 80mm bore offers 2513 N of push, while stepping up to the 125mm bore yields 6136 N for heavier payloads. Because the SE100AX160S is dimensionally interchangeable per ISO 15552, it serves as a direct drop-in replacement for other ISO 15552 profile cylinders, sharing standard mounting hardware. Ensure your setup specifies the PT1/2 port, the -S magnet for CMSE/DMSE sensors, and the SUS420J2 rod for washdown duty.
Note that a plain SE cylinder cannot hold a load if air pressure is lost; the adjustable air cushion only decelerates the piston near stroke end and does not act as a mechanical brake. For position-holding safety, consider the BSE rod lock variant. With a 160mm stroke, side loads are generally moderate, but always verify rod-bearing bending limits and use an external guide if the load is heavily offset.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE100 Standard Air Cylinder SE100AX160S FAQ
The SE100AX160S features a 100mm bore with a PT1/2 port. At 0.5 MPa it provides 3927 N push and 3681 N pull; at 0.7 MPa it provides 5497 N push. The maximum push force is 801 kgf at 1.0 MPa.
It is dimensionally interchangeable per ISO 15552, serving as a drop-in replacement for other standard profile cylinders. However, it is double-acting and cannot hold a load without live air pressure; the adjustable cushion only decelerates the piston near stroke end and is not a locking brake.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE100 Standard Air Cylinder SE100AX160S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.