Airtac SE100 Standard Air Cylinder SE100AX200S
The AirTAC Airtac SE100 Standard Air Cylinder SE100AX200S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 200mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke200 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE100 Standard Air Cylinder SE100AX200S
The AirTAC SE100AX200S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty motion. It delivers a substantial 3927 N push force at 0.5 MPa and pulls 3681 N, making it well-suited for high-load pressing and forming tasks. The extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly in tight machine cavities.
This specific configuration includes a SUS420J2 stainless steel rod (code A) for washdown and corrosive environments, alongside a built-in magnet (code S) for position sensing. The barrel houses sensor grooves on three sides, allowing flexible mounting of CMSE reed or DMSE electronic switches. Furthermore, the field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune deceleration via a screw, softening hard end stops during high-speed cycling.
Airtac SE100 Standard Air Cylinder SE100AX200S Technical Specifications
| Model | Airtac SE100 Standard Air Cylinder SE100AX200S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE100 Standard Air Cylinder SE100AX200S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE100 Standard Air Cylinder SE100AX200S Is Used
Injection Mold Clamping
Provides the 3927 N push force required to secure heavy injection mold halves during polymer injection cycles.
Pallet Diverter Arm
Uses the 200mm stroke to actuate heavy diverting mechanisms that re-route loaded pallets on packaging conveyors.
Hydro-Pneumatic Press
Drives the primary ram in a 100mm bore hydro-pneumatic press, leveraging the SUS420J2 rod for fluid resistance.
Is the Airtac SE100 Standard Air Cylinder SE100AX200S the Right Cylinder?
When sizing this 100mm bore actuator, evaluate your exact force requirements: stepping down to the 80mm bore drops the 0.5 MPa push to 2513 N, while stepping up to the 125mm bore increases it to 6136 N. The 200mm stroke moves substantial loads but remember that a plain SE cylinder cannot hold a load if air pressure is lost or the valve is centered—the piston will drift. For critical position-holding without live pressure, consider the BSE rod-lock variant or an external pilot-operated check valve. Because it adheres to the ISO 15552 / VDMA 24562 interface, this model serves as a drop-in dimensional replacement for other ISO 15552 cylinders, utilizing the same PT1/2 port, M20x1.5 rod thread, and standardized mounting accessories.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE100 Standard Air Cylinder SE100AX200S FAQ
This 100mm bore cylinder delivers a push force of 3927 N and a pull force of 3681 N at 0.5 MPa. At 0.7 MPa, the push force is 5497 N, with a maximum push of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE100AX200S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. It shares the exact same mounting footprint, PT1/2 port, and M20x1.5 rod thread as other standard profile cylinders, ensuring a seamless retrofit.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE100 Standard Air Cylinder SE100AX200S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.