Airtac SE100 Standard Air Cylinder SE100BX200SH
The AirTAC Airtac SE100 Standard Air Cylinder SE100BX200SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 200mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke200 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE100 Standard Air Cylinder SE100BX200SH
The AirTAC SE100BX200SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty performance. It delivers a substantial 3927 N push at 0.5 MPa and up to 801 kgf maximum force at 1.0 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight machinery frames while retaining the standardized ISO 15552 mounting interface.
This specific configuration pairs a SUS304 stainless steel rod (code B) for superior washdown and corrosive-environment resilience with a high-temperature Viton FKM seal (code H), extending the operating range from -20 to +150 C. The integrated magnet (code S) enables precise end-of-stroke detection using AirTAC CMSE reed or DMSE electronic sensors. Field-adjustable pneumatic cushioning at both ends allows you to tune deceleration and soften hard end stops at high cycling speeds.
Airtac SE100 Standard Air Cylinder SE100BX200SH Technical Specifications
| Model | Airtac SE100 Standard Air Cylinder SE100BX200SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE100 Standard Air Cylinder SE100BX200SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE100 Standard Air Cylinder SE100BX200SH Is Used
Injection Mold Unloading
Leveraging 3927 N of push force at 0.5 MPa, this cylinder reliably extracts heavy plastic injection molds from presses, while the SUS304 rod resists corrosive release agents.
Pallet Forming Press
The 200 mm stroke provides the precise travel needed to compact and seal large packaging cartons, utilizing the field-adjustable cushion to soften the 801 kgf end-of-stroke impact.
Chemical Dispense Valve
Actuating heavy-duty process valves in chemical plants, the Viton FKM seal withstands 150 C thermal loads and aggressive solvents while the DMSE sensor tracks positioning.
Is the Airtac SE100 Standard Air Cylinder SE100BX200SH the Right Cylinder?
Selecting this 100 mm bore makes sense when your application requires substantial thrust, pushing 3927 N at 0.5 MPa. If your load is lighter, stepping down to the 80 mm bore yields 2513 N push, whereas stepping up to the 125 mm bore provides 6136 N push. Because the 200 mm stroke is below the 300 mm side-load threshold, the 25 mm rod and M20x1.5 thread handle standard bending stresses well, though any long unsupported load still requires an external guide. For drop-in retrofits, verify the PT1/2 port, 200 mm stroke, and your specific mounting accessory. Remember that a standard SE does not hold a load when air pressure is lost; if your process requires position holding without live pressure, consider the BSE rod-lock variant instead.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE100 Standard Air Cylinder SE100BX200SH FAQ
This 100 mm bore cylinder delivers 3927 N push and 3681 N pull at 0.5 MPa, 5497 N push at 0.7 MPa, and a maximum push of 801 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s, uses a PT1/2 port, and features a SUS304 rod with a Viton FKM seal rated for -20 to +150 C.
Yes, the SE100BX200SH is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards, allowing it to drop into existing footprints and share mounting hardware like FA flanges or TC trunnions. The extruded aluminum profile body lacks external tie rods, making it highly compact while maintaining full standard compatibility.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE100 Standard Air Cylinder SE100BX200SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.