Airtac SE100 Standard Air Cylinder SE100BX500SH
The AirTAC Airtac SE100 Standard Air Cylinder SE100BX500SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 500mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke500 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE100 Standard Air Cylinder SE100BX500SH
The AirTAC SE100BX500SH is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 standard. It delivers a substantial 3927 N push force at 0.5 MPa, utilizing a 100 mm bore and 500 mm stroke to drive heavy actuators. The square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant profile that simplifies mounting flush against machine frames.
This specific configuration pairs a SUS304 stainless steel rod with a Viton (FKM) seal, extending the operating temperature range up to 150 C for corrosive or washdown environments. A built-in magnet (-S) enables position detection via CMSE reed or DMSE electronic sensors. Field-adjustable pneumatic cushioning at both ends allows precise tuning of end-of-stroke deceleration to absorb kinetic energy from heavy 100 mm payloads.
Airtac SE100 Standard Air Cylinder SE100BX500SH Technical Specifications
| Model | Airtac SE100 Standard Air Cylinder SE100BX500SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 500 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE100 Standard Air Cylinder SE100BX500SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE100 Standard Air Cylinder SE100BX500SH Is Used
Injection Mold Clamping
Provides the 3927 N push force required to secure heavy injection mold halves during high-temperature plastic injection cycles.
Pallet Strapping Press
Drives the sealing head on automated pallet strapping equipment, where the 500 mm stroke accommodates oversized pallet heights.
Industrial Oven Doors
Opens and closes heavy industrial oven doors, leveraging the Viton seal and SUS304 rod to withstand continuous 150 C heat.
Is the Airtac SE100 Standard Air Cylinder SE100BX500SH the Right Cylinder?
This 100 mm bore generates 3927 N push at 0.5 MPa, making it ideal for heavy presses. If you need less force, the 80 mm bore provides 2513 N push; if your payload is higher, the 125 mm bore offers 6136 N. Because the 500 mm stroke leaves the 25 mm rod unsupported for a long distance, an external guide is strongly recommended to prevent rod-bearing bending under side loads.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a drop-in replacement for other ISO 15552 profile cylinders. To match this exact unit, specify: 100 mm bore, 500 mm stroke, PT1/2 port, Basic mounting, SUS304 rod (B), FKM seal (H), and a magnet (S). Note that the air cushion only decelerates the piston near stroke end; it does not hold the load if air pressure is lost.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE100 Standard Air Cylinder SE100BX500SH FAQ
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa.
Yes, the SE100BX500SH shares the standardized ISO 15552 mounting interface, making it a drop-in replacement for other ISO 15552 profile cylinders. The built-in magnet works with AirTAC CMSE and DMSE sensors for position feedback.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE100 Standard Air Cylinder SE100BX500SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.