Airtac SE100 Standard Air Cylinder SE100X240S
The AirTAC Airtac SE100 Standard Air Cylinder SE100X240S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 240mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke240 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE100 Standard Air Cylinder SE100X240S
The AirTAC SE100X240S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 3927 N push at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. Equipped with a built-in magnet, this unit directly supports AirTAC CMSE reed and DMSE electronic position sensors for precise end-of-stroke verification.
Field-adjustable pneumatic cushioning at both ends allows technicians to tune the deceleration of the 25 mm piston rod via a set screw, softening hard end stops during high-speed operations up to 800 mm/s. Because this is a standard 100 mm bore with a 240 mm stroke, it drops seamlessly into existing ISO 15552 footprints without requiring custom mounting hardware.
Airtac SE100 Standard Air Cylinder SE100X240S Technical Specifications
| Model | Airtac SE100 Standard Air Cylinder SE100X240S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 240 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE100 Standard Air Cylinder SE100X240S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×240 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE100 Standard Air Cylinder SE100X240S Is Used
Press Brake Tooling
Provides the 5497 N push force at 0.7 MPa needed to actuate heavy lower clamps on automated metal press brakes, ensuring secure die seating.
Pallet Dispenser
Uses the 240 mm stroke and 801 kgf max thrust to push empty wooden pallets into magazine staging lanes before the automated stretch wrapper.
Injection Mold Ejector
Leverages the built-in magnet and DMSE electronic sensors to confirm full retraction of heavy mold halves before the next high-pressure plastic injection cycle.
Is the Airtac SE100 Standard Air Cylinder SE100X240S the Right Cylinder?
Selecting this 100 mm bore makes sense when your application requires substantial thrust, specifically 3927 N of push force at 0.5 MPa or 801 kgf at the 1.0 MPa maximum. If you need to scale down, the 80 mm neighbor provides 2513 N of push, while stepping up to the 125 mm bore yields 6136 N, allowing you to size the actuator accurately in either direction based on your actual load. This SE100X240S configuration includes the -S magnet for switch tracking and uses a PT1/2 port.
Remember that the adjustable air cushion only decelerates the piston near the stroke end; it does not lock or hold the load. If air pressure drops or the valve centers, the rod will drift, so any vertical load requires an external rod lock like the BSE series or a pilot-operated check valve. Additionally, while the 25 mm rod handles high side loads well, any stroke over 300 mm demands an external guide to prevent rod-bearing bending.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE100 Standard Air Cylinder SE100X240S FAQ
The SE100X240S delivers a push force of 3927 N and a pull force of 3681 N at 0.5 MPa. At 0.7 MPa, the push force is 5497 N, with an absolute maximum push of 801 kgf at 1.0 MPa. The operating speed ranges from 30-800 mm/s.
Yes, the SE100X240S is dimensionally interchangeable per ISO 15552. You can drop it in as a replacement for other ISO 15552 profile cylinders, matching the 100 mm bore, 240 mm stroke, PT1/2 port, and standard mounting accessories without machining new holes.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE100 Standard Air Cylinder SE100X240S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.