Airtac SE100 Standard Air Cylinder SE100X250
The AirTAC Airtac SE100 Standard Air Cylinder SE100X250 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 250mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke250 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE100 Standard Air Cylinder SE100X250
The AirTAC SE100X250 is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. Operating at 0.5 MPa, it delivers 3927 N of push force and 3681 N of pull force, scaling up to a maximum 801 kgf at 1.0 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This 100 mm bore unit features a PT1/2 port and a 25 mm hard-chrome plated rod with an M20x1.5 thread. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, softening hard impacts during high-speed 30-800 mm/s cycles. This specific SKU lacks the -S magnet option, meaning it is not equipped out-of-the-box for CMSE or DMSE position sensing.
Airtac SE100 Standard Air Cylinder SE100X250 Technical Specifications
| Model | Airtac SE100 Standard Air Cylinder SE100X250 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 250 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE100 Standard Air Cylinder SE100X250
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE100 Standard Air Cylinder SE100X250 Is Used
Metal Stamping Press
Provides the 3927 N push force at 0.5 MPa required to drive small stamping dies and form light-gauge sheet metal components.
Pallet Diverting Arm
Uses the 250 mm stroke to extend a heavy redirecting arm, smoothly shunting loaded pallets between adjacent conveyor lines.
Injection Mold Ejection
Cycles at 30-800 mm/s to push finished plastic parts out of injection molds, relying on adjustable cushions to soften end stops.
Is the Airtac SE100 Standard Air Cylinder SE100X250 the Right Cylinder?
Generating 3927 N push at 0.5 MPa, this 100 mm bore cylinder is suited for high-force pressing and heavy lifting. If your load demands less force, the neighbouring 80 mm bore provides 2513 N of push at 0.5 MPa; conversely, stepping up to the 125 mm bore yields 6136 N for heavier requirements. As a true ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for other ISO 15552 cylinders, sharing standard mounting hardware like FA front flanges or TC trunnions.
Because the 250 mm stroke creates an extended lever arm on the 25 mm rod, unsupported loads induce bending moments on the rod bearing. For optimal seal life and to prevent premature wear, incorporate an external guide rail to absorb lateral stresses. Note that the double-acting air cushion only decelerates the piston near stroke end and does not hold the load if air pressure is lost; for static holding, a BSE rod lock variant is required.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE100 Standard Air Cylinder SE100X250 FAQ
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE100X250 features a standardized ISO 15552 mounting interface and a PT1/2 port, making it dimensionally interchangeable with other ISO 15552 profile cylinders. You can reuse existing mounting brackets and hardware without modifying the machine frame.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE100 Standard Air Cylinder SE100X250
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.