The AirTAC AirTAC SE100X275S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 275mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X275S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. It delivers a substantial 3927 N push force at 0.5 MPa, utilizing a 100 mm bore and a 275 mm stroke. The extruded aluminum barrel design omits external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames while freeing up perimeter space for valves and manifolds.
Equipped with a built-in magnet (-S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable air cushions at both ends allow technicians to tune deceleration via a set screw, effectively softening hard end stops during high-velocity 30-800 mm/s cycles.
| Model | AirTAC SE100X275S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 275 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×275 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 3927 N of extend force at 0.5 MPa to drive small stamping dies and form light-gauge sheet metal components over a 275 mm stroke.
Actuates a heavy diverter gate on a packaging conveyor, using the 275 mm stroke to push loaded pallets onto a secondary processing line.
Ejects dense plastic molded parts from heavy tooling, relying on the smooth profile barrel for flush mounting and the -S magnet for DMSE timing.
Selecting the SE100X275S is optimal when your mechanism requires heavy linear thrust within a 275 mm travel envelope. If 3927 N of push at 0.5 MPa exceeds your requirement, stepping down to the 80 mm bore yields 2513 N, saving compressed air volume. Conversely, scaling up to the 125 mm bore provides 6136 N for highly demanding press operations. Because this is a 275 mm stroke, the 25 mm rod and its bearing face bending moments under heavy lateral loads; integrating an external guide rail prevents premature gland wear and preserves seal integrity.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a drop-in replacement for standardized 100 mm bore hardware, utilizing a PT1/2 port and a 36 mm cushion length. Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not lock or hold the load. If your fixture must maintain vertical position during a compressed air loss, pair this cylinder with an external pilot-operated check valve or transition to the BSE rod-lock variant.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force reaches 5497 N, with a maximum push of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE100X275s is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint, PT1/2 port size, and M20x1.5 rod thread of other standard profile cylinders for seamless retrofitting.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.