The AirTAC AirTAC SE100X280 ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 280mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X280 is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It utilizes a square extruded aluminum barrel that eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. Delivering a substantial 3927 N push at 0.5 MPa, this 100 mm bore unit is built for rigorous industrial cycles.
Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when moving heavy loads at speed. This specific SKU is configured without a position sensor magnet and uses a standard PT1/2 port. The robust Ø25 mm hard-chrome rod and M20x1.5 thread provide high rigidity for demanding push and pull tasks.
| Model | AirTAC SE100X280 ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 280 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×280 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the robust 3927 N push force at 0.5 MPa required to eject heavy plastic injection molded parts from the tool face without deflection.
Leverages the 280 mm stroke to swing heavy pallets onto a secondary conveyor line, relying on the adjustable cushion to absorb the kinetic energy of the shifting mass.
Feeds heavy steel blanks into a hydraulic press, utilizing the rigid Ø25 mm rod to maintain alignment under the high impact forces of an automated fabrication cell.
Selecting this 100 mm bore cylinder makes sense when your application requires substantial thrust, specifically 3927 N of push force at 0.5 MPa. If you need slightly less force, stepping down to the 80 mm bore yields 2513 N at 0.5 MPa. Conversely, if you need maximum thrust, stepping up to the 125 mm bore provides 6136 N at 0.5 MPa. Because this is a plain double-acting cylinder, it will not hold a load if air pressure is lost or the valve is centered; a load-holding application requires a BSE rod lock variant or an external pilot-operated check valve.
With a 280 mm stroke, the internal rod bearing experiences increased bending moments under side loads. For optimal seal life and to prevent rod scoring, always pair this cylinder with an external guide rail to support the load rather than relying on the rod alone. As a true ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for other standard ISO 15552 cylinders, sharing identical mounting and PT1/2 port interfaces.
Quick checklist
The SE100X280 delivers a push force of 3927 N and a pull force of 3681 N at 0.5 MPa. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE100X280 features a standard ISO 15552 profile body without external tie rods, making it dimensionally interchangeable with other ISO 15552 cylinders. It shares the standardized mounting interface, PT1/2 port, and M20x1.5 rod thread for a direct retrofit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.