The AirTAC AirTAC SE100X290 ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 290mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X290 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a robust 3927 N push force at 0.5 MPa. Featuring a 100 mm bore and 290 mm stroke, it uses a PT1/2 port and a Ø25 mm hard-chrome plated rod with an M20x1.5 thread. The square extruded aluminum barrel omits external tie rods, yielding a flush, compact body that resists corrosion and simplifies mounting on tight machine frames.
Unlike fixed rubber bumpers, this actuator features a field-adjustable pneumatic cushion at both ends, allowing technicians to dial in end-of-stroke deceleration via a set screw to soften hard impacts at high cycle rates. Note that this specific SKU ships without a built-in magnet, so it does not directly support CMSE or DMSE electronic position sensing without modification. The cushion mechanism strictly decelerates the piston near stroke end and does not lock or hold the load if air pressure is lost.
| Model | AirTAC SE100X290 ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 290 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×290 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Handles the 3927 N push at 0.5 MPa required to positively index heavy corrugated cardboard cases onto a palletizing conveyor line.
Uses the 290 mm stroke and Ø25 mm rod to drive heavy plastic injection mold ejection plates out of the machine safely.
Provides the robust clamping force needed to hold and position heavy upper press brake tooling assemblies during changeovers.
Generating 3927 N of push at 0.5 MPa, this 100 mm bore is a heavy-duty workhorse. If your application requires less force, stepping down to the 80 mm bore yields 2513 N of push, whereas scaling up to the 125 mm bore provides 6136 N for heavier fixtures. Because this is a 290 mm stroke, the extended unsupported rod length increases the risk of rod-bearing bending under lateral loads; utilizing an external guide rail is strongly recommended to prevent premature seal wear.
As a true ISO 15552 profile cylinder, the SE100X290 is dimensionally interchangeable with other ISO 15552 cylinders, making it a seamless drop-in retrofit that reuses your existing mounting hardware. To match this exact configuration, specify the 100 mm bore, 290 mm stroke, PT1/2 port, and your preferred mounting accessory (such as FA or TC). Remember that a plain SE cylinder will drift if air is exhausted; if your machine requires true mid-stroke position holding without live pressure, consider the BSE rod-lock variant instead.
Quick checklist
The SE100X290 generates 3927 N push and 3681 N pull at 0.5 MPa, 5497 N push at 0.7 MPa, and a maximum push of 801 kgf at 1.0 MPa. It operates at speeds ranging from 30 to 800 mm/s.
Yes, the SE100X290 is dimensionally interchangeable per ISO 15552 standards, meaning it serves as a drop-in replacement for other ISO 15552 profile cylinders using your existing mounting brackets and front PT1/2 port locations.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.