The AirTAC AirTAC SE100X300H ISO 15552 Cylinder | 100mm Viton is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 300mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X300H is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 3927 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact body that mounts flush against machine frames while resisting corrosion. The FKM (Viton) seal extends the operating temperature range up to 150 C, making it well-suited for hot environments where standard TPU elastomers would fail.
This 100 mm bore unit travels a 300 mm stroke and relies on field-adjustable pneumatic cushioning at both ends to decelerate heavy loads smoothly. You can tune the cushion screws to soften hard end-stops, preventing impact damage without relying on fixed rubber bumpers. Because this SKU lacks the -S magnet code, it does not support direct position sensing via CMSE or DMSE switches.
| Model | AirTAC SE100X300H ISO 15552 Cylinder | 100mm Viton |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 300 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives heavy mold ejector pins in hot environments, utilizing the 3927 N push force and 150 C Viton seal to withstand ambient radiant heat near the press.
Actuates heavy-duty lifting arms in a rolling mill, where the 300 mm stroke provides the reach needed to clear the coil core and the FKM seal resists thermal degradation.
Indexes empty pallet stacks via a 300 mm stroke, relying on the 5497 N extend force at 0.7 MPa to overcome mechanical friction in dusty, high-temperature packaging lines.
Selecting this 100 mm bore provides 3927 N of push at 0.5 MPa. If your application requires less force, the neighboring 80 mm bore offers 2513 N, while stepping up to the 125 mm bore yields 6136 N for heavier demands. This model uses a PT1/2 port and M20x1.5 rod thread, so ensure your plumbing and clevis joints match these dimensions for a drop-in ISO 15552 retrofit.
Because the stroke is 300 mm, the extended rod is subject to bending forces under side loads; always use an external guide mechanism to prevent rod-bearing wear. Note that the adjustable air cushion only decelerates the piston near the stroke ends and will not hold a load if air pressure drops. If your process requires position holding without live pressure, consider the BSE rod-lock variant.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N, with a maximum push capacity of 801 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable with other ISO 15552 profile cylinders, sharing standard mounting and PT1/2 port dimensions. The H seal option designates a Viton (FKM) seal, expanding the operating temperature range up to 150 C for high-heat applications.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.