The AirTAC AirTAC SE100X320S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 320mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X320S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics, delivering a robust 3927 N push force at 0.5 MPa. Its extruded aluminum barrel design omits external tie rods entirely, yielding a highly compact, corrosion-resistant body that mounts flush within tight machine frames while maintaining standardized dimensional interchangeability.
This 100mm bore unit incorporates a built-in magnet (-S) designed to interface seamlessly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to tune end-cap deceleration via a set screw, softening hard mechanical stops during high-velocity 320mm strokes.
| Model | AirTAC SE100X320S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 320 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×320 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 3927 N push force at 0.5 MPa to positively index heavy corrugated cardboard cases onto a palletizing conveyor during continuous packaging line operations.
Leverages the 320mm stroke and built-in DMSE electronic sensor magnet to drive a secondary parts ejector plate on a large-tonnage injection molding machine.
Deploys the 801 kgf maximum thrust to feed heavy-gauge steel blanks into a hydraulic forming press, utilizing the adjustable cushion to halt the 100mm piston smoothly.
Generating 3927 N of push force at 0.5 MPa, this 100mm bore is sized for substantial loads. If your application requires less force, stepping down to the 80mm bore yields 2513 N of push, whereas moving up to the 125mm bore provides 6136 N for heavier assemblies. Because the 320mm stroke exceeds 300mm, the unsupported piston rod is subject to bending moments under side loads; integrating an external guide rail is strongly recommended to prevent premature rod-bearing wear.
As a standard ISO 15552 cylinder, it serves as a direct dimensional drop-in replacement for equivalent profile cylinders, matching the 100mm bore, 320mm stroke, PT1/2 port, and standard mounting accessories. Note that the adjustable air cushion only decelerates the piston near the stroke ends; it does not lock or hold the load. If unpowered position holding is required, integrate an external pilot-operated check valve or specify a BSE rod-lock variant.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE100X320S is dimensionally interchangeable per ISO 15552 standards. It shares the exact 100mm bore, 320mm stroke, PT1/2 port, and standardized mounting interface, allowing it to drop into existing foot or flange mounts without frame modifications.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.