The AirTAC AirTAC SE100X330S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 330mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X330S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. It delivers a robust 3927 N push force at 0.5 MPa, utilizing a 100mm bore and 330mm stroke. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit seamlessly integrates AirTAC CMSE reed and DMSE electronic position sensors along the three integrated sensor grooves. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed cycling.
| Model | AirTAC SE100X330S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 330 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×330 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 5497 N extension force at 0.7 MPa required to positively eject heavy molded plastic parts from a press platen over a 330mm extraction distance.
Actuates a heavy-duty routing gate on a 50kg logistics conveyor, using the integrated -S magnet and DMSE sensor to confirm full stroke positioning.
Transfers heavy steel blanks into a hydraulic press, utilizing the 36mm adjustable cushion to smoothly decelerate the 25mm rod before the end cap.
When sizing this 100mm bore actuator, compare its 3927 N push at 0.5 MPa against the neighboring bores. Stepping down to an 80mm cylinder yields 2513 N of push force, while stepping up to a 125mm bore provides 6136 N. This SE100X330S features a PT1/2 port and a 25mm piston rod, making it dimensionally interchangeable with other ISO 15552 cylinders for straightforward retrofits.
Because the 330mm stroke creates a long lever arm, side loads will induce significant bending moments on the rod bearing. Always pair this cylinder with an external guide rail to prevent premature seal wear. Note that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking device. If the application must hold a vertical load without live air pressure, utilize a BSE rod lock variant or an external pilot-operated check valve.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes. The SE100X330S is dimensionally interchangeable per ISO 15552 standards. You can use your existing mounting hardware and drop it in as a replacement for other ISO 15552 profile cylinders, provided the PT1/2 port and M20x1.5 rod thread match your setup.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.