The AirTAC AirTAC SE100X35 ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 35mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X35 is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty positioning, delivering 3927 N of push force at 0.5 MPa. Its square extruded aluminum barrel entirely eliminates external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly against machine frames without protruding hardware.
This 100mm bore unit features a Ø25mm piston rod and a PT1/2 port. Because this specific SKU lacks the -S magnet code, it is not prepped for AirTAC CMSE or DMSE electronic position sensing out of the box. Field-adjustable pneumatic cushioning at both stroke ends allows technicians to dial out harsh end-stop impacts during high-speed cycling.
| Model | AirTAC SE100X35 ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 35 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 3927 N of extend force at 0.5 MPa to hold medium-sized injection mold halves securely shut during low-pressure close sequences.
Acts as a heavy-duty physical stop mechanism on pallet conveyor lines, using its 35mm stroke to raise and lower a blocking blade robustly.
Drives large-diameter dowel pins into heavy steel assemblies, utilizing the 100mm bore's 801 kgf maximum thrust to seat components without an external hydraulic pump.
In the SE lineup, this 100mm bore outputs 3927 N push at 0.5 MPa. If your application requires less force, the 80mm bore neighbor provides 2513 N, while stepping up to the 125mm bore yields 6136 N for heavier loads. As a standard double-acting cylinder, this model will drift if air pressure is lost or the valve is centered; for fail-safe load holding, consider the BSE rod-lock variant or an external pilot-operated check valve. With its 35mm stroke, side-load stress on the rod bearing is minimal compared to longer 300mm+ strokes.
Quick checklist
The SE100X35 generates 3927 N of push force and 3681 N of pull force at 0.5 MPa. At 0.7 MPa, the push force reaches 5497 N. The absolute maximum push force is 801 kgf when operating at the 1.0 MPa pressure limit.
Yes, the SE100X35 is dimensionally interchangeable per ISO 15552 standards. Its standardized mounting interface and PT1/2 port allow it to serve as a direct drop-in replacement for other ISO 15552 profile cylinders, sharing identical mounting hole patterns and rod thread dimensions.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.