The AirTAC AirTAC SE100X370 ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 370mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X370 is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 3927 N push force at 0.5 MPa. Its extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This clean profile simplifies fabrication while maintaining the rigorous dimensional footprint required for global interchangeability.
This specific SKU lacks the built-in magnet option, meaning it operates without electronic position feedback out of the box. Deceleration at both stroke ends is handled by a field-adjustable air cushion rather than a fixed rubber bumper, allowing technicians to tune the end-of-stroke deceleration via a set screw to soften hard impacts at operating speeds up to 800 mm/s.
| Model | AirTAC SE100X370 ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 370 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×370 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the heavy 3927 N extend force needed to eject dense plastic parts from injection molding platens, with adjustable cushioning absorbing the sudden deceleration over the 370 mm travel.
Drives a sweeping arm to redirect heavy timber pallets on a packaging line, utilizing the 100 mm bore's high push capacity to overcome lateral friction without stalling.
Pushes raw steel billets into the heating chamber of a hydraulic press, where the tie-rod-free extruded profile allows the cylinder to sit flush in a confined, high-temperature ambient zone.
Selecting this 100 mm bore makes sense when your application requires substantial thrust, pushing 3927 N at 0.5 MPa or 5497 N at 0.7 MPa. If your load demands less force, stepping down to the 80 mm bore yields 2513 N of push at 0.5 MPa, whereas moving up to the 125 mm bore provides 6136 N. Because this unit has a 370 mm stroke, the extended 25 mm rod and internal bearing face bending moments under heavy side loads; always incorporate an external guide rail to prevent premature seal wear. As a standard ISO 15552 cylinder with a PT1/2 port, it serves as a direct dimensional replacement for competing profile cylinders. Note that a plain SE cylinder will drift if air pressure is lost or the valve is centered—it cannot hold a load without live pressure, so specify a BSE rod lock variant if static holding is required.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder outputs 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N. The maximum push force is 801 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE100X370 shares the exact ISO 15552 / VDMA 24562 mounting interface and PT1/2 port geometry, allowing it to serve as a drop-in dimensional replacement for other standard profile cylinders. Just ensure your mounting hardware matches the standard FA or FB flanges.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.