The AirTAC AirTAC SE100X375S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 375mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X375S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 3927 N push at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The integrated -S magnet enables direct position tracking with AirTAC CMSE reed or DMSE electronic sensors.
Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when moving heavy loads at speed. With a 100 mm bore, PT1/2 port, and 375 mm stroke, this cylinder excels in high-thrust linear actuation where precise stopping control is essential.
| Model | AirTAC SE100X375S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 375 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×375 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 5497 N push force at 0.7 MPa required to eject heavy stamped metal sheets from press dies, utilizing the 375 mm stroke to clear the lower bolster completely.
Secures injection molding tooling halves with 801 kgf maximum thrust, while the adjustable cushion softens the high-speed approach to protect expensive mold faces.
Actuates heavy-duty diverting arms on automated packaging lines, using the built-in magnet to confirm full extension before a pallet transitions lanes.
This 100 mm bore generates 3927 N of push force at 0.5 MPa. If your application requires less thrust, the 80 mm bore offers 2513 N; if you need significantly more power, the 125 mm bore provides 6136 N. Because the 375 mm stroke creates a long lever arm on the M20x1.5 rod, external guide rails should be used to prevent side-loading damage to the rod bearing.
As a standard ISO 15552 profile cylinder, the SE100X375S is dimensionally interchangeable with other ISO 15552 cylinders, allowing direct retrofitting using existing mounting hardware. Note that the adjustable air cushion only decelerates the piston near stroke end and does not lock the load; if position holding is required without live air pressure, consider the BSE rod lock variant.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE100X375S is dimensionally interchangeable per ISO 15552, meaning it shares the exact same mounting footprint and port sizes (PT1/2) as other standard ISO 15552 profile cylinders, allowing a direct drop-in replacement.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.