The AirTAC AirTAC SE100X390S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 390mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X390S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It delivers a substantial 3927 N push force at 0.5 MPa, utilizing a 100 mm bore and a 390 mm stroke. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for universal hardware interchangeability.
Equipped with a built-in magnet (-S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to dial in end-stop deceleration via a set screw, softening impacts when moving heavy loads at high velocities. Remember that this pneumatic cushion only decelerates the piston near stroke end; it does not lock or hold the load if air pressure drops.
| Model | AirTAC SE100X390S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 390 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×390 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 3927 N of extend force at 0.5 MPa to secure heavy machining pallets against a VMC tombstone, using the 390 mm stroke to reach across wide work envelopes.
Actuates a routing gate on a chain conveyor, relying on the adjustable end cushions to soften the stop when redirecting 500 kg assembly pallets at speed.
Ejects formed metal blanks from a 100-ton press bed, utilizing the integrated CMSE/DMSE magnet to signal the press controller that the ejector is fully retracted.
Selecting the SE100X390S is appropriate when your application requires roughly 3927 N of push force at 0.5 MPa or up to 801 kgf at 1.0 MPa. If your load demands less force, stepping down to the 80 mm bore provides 2513 N of push at 0.5 MPa, whereas scaling up to the 125 mm bore yields 6136 N for heavier rigging. Because this model features a 390 mm stroke, the 25 mm rod and front bearing face bending moments under lateral stress; always incorporate an external guide rail to prevent side-load damage and premature seal wear. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct drop-in replacement for other ISO 15552 profile cylinders, utilizing a PT1/2 port and standard mounting accessories.
Quick checklist
At 0.5 MPa, the SE100X390S generates 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N, with a maximum push capacity of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No, the adjustable air cushion at both ends only decelerates the piston near the stroke limits and acts as a bumper, not a brake. If air is exhausted or pressure drops, the piston will drift. For position holding, use a BSE rod lock variant or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.