The AirTAC AirTAC SE100X40SH ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 40mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X40SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty motion control. It delivers a robust 3927 N push force at 0.5 MPa and features a 40 mm stroke. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight machinery spaces.
Equipped with a Viton (FKM) seal, this unit withstands operating temperatures up to 150 C for high-heat industrial environments. The integrated -S magnet supports position detection via AirTAC CMSE reed or DMSE electronic sensors, while the field-adjustable air cushioning at both ends allows precise deceleration tuning to eliminate hard end-stops.
| Model | AirTAC SE100X40SH ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 3927 N of clamping force at 0.5 MPa for securing plastic injection mold halves, leveraging the FKM seal to survive ambient heat radiating from the mold bases.
Actuates heavy sealing jaws on continuous flow wrappers, where the 150 C FKM Viton seal resists degradation from nearby heated glue applicators.
Drives 801 kgf at 1.0 MPa to eject thick-gauge stamped metal parts from progressive dies, using adjustable end cushions to absorb high kinetic energy.
If your application requires less force, stepping down to the 80 mm bore yields a 2513 N push at 0.5 MPa, whereas moving up to the 125 mm bore provides a 6136 N push. As an ISO 15552 standard cylinder, this model is dimensionally interchangeable with other ISO 15552 cylinders, simplifying retrofits. It uses a PT1/2 port, a Ø25 mm rod with an M20x1.5 thread, and the -S magnet. Note that this plain cylinder cannot hold a load if air pressure is lost; for position holding, consider the BSE rod lock variant. Because the stroke is only 40 mm, side-load bending is minimal, but always verify rod bearing loads.
Quick checklist
At 0.5 MPa, the SE100X40SH generates 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa.
Yes, the SE100X40SH is dimensionally interchangeable per ISO 15552 standards, allowing it to serve as a drop-in replacement for other ISO 15552 profile cylinders using existing mounting hardware.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.