The AirTAC AirTAC SE100X440S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 440mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X440S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. It generates a substantial 3927 N push at 0.5 MPa, scaling up to 5497 N at 0.7 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 dimensions for seamless retrofitting.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune the deceleration of the 25 mm rod via a set screw, softening hard impacts when moving heavy payloads across its 440 mm travel.
| Model | AirTAC SE100X440S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 440 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×440 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 5497 N push force at 0.7 MPa required to eject heavy stamped metal sheets from press dies, utilizing the 440 mm stroke to clear the lower bolster completely.
Actuates heavy-duty lane diverters on automated packaging conveyors, where the no-tie-rod profile allows flush mounting into tight framework and the -S magnet confirms divert position.
Handles secondary mold clamping or core pulling on mid-sized injection molding machines, leveraging the adjustable cushion to soften the stop when shifting heavy mold components.
When sizing this 100 mm bore actuator, compare its 3927 N push at 0.5 MPa against neighboring bores. Stepping down to the 80 mm bore yields 2513 N, whereas the larger 125 mm bore provides 6136 N. If your process demands holding a load vertically without continuous air pressure, note that a standard SE cylinder will drift; you should integrate an external pilot-operated check valve or transition to the BSE rod-lock variant for secure clamping.
Because this model features a 440 mm stroke, the extended 25 mm rod is subject to bending forces under heavy side loads. To prevent premature rod-bearing wear, mount an external guide rail to support the payload rather than relying on the cylinder itself to absorb lateral moments. This drop-in replacement shares the PT1/2 port and standard mounting interface of any ISO 15552 cylinder, simplifying your procurement pipeline.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force reaches 5497 N. The maximum push force is 801 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE100X440S is dimensionally interchangeable per ISO 15552. You can drop it in as a replacement for other ISO 15552 profile cylinders, matching the PT1/2 port and standard mounting accessories without altering your machine footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.