The AirTAC AirTAC SE100X450SFA ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 450mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X450SFA is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty positioning. Operating at 0.5 MPa, it generates 3927 N of push force and 3681 N of pull force, scaling up to a maximum of 801 kgf at 1.0 MPa. The FA front flange mounting secures the body firmly for rigid thrust transfer.
This 100 mm bore unit features a square extruded aluminum barrel without external tie rods, offering a compact, corrosion-resistant profile that mounts flush against machine frames. The integrated -S magnet allows seamless position detection using AirTAC CMSE reed or DMSE electronic sensors. Furthermore, field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed cycling.
| Model | AirTAC SE100X450SFA ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 450 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives a 450 mm stroke to push filled corrugated cases onto a palletizing layer, utilizing the 3927 N push force to overcome carton drag and guide resistance.
Mounts via the FA front flange to deliver a rigid 801 kgf max breakout force, stripping large molded plastic automotive fascias from heavy tooling cores.
Advances heavy-gauge steel sheets into a press brake over a 450 mm travel, relying on the field-adjustable cushion to soften end-of-stroke stops at high speed.
If your assembly requires less thrust, the 80 mm bore provides 2513 N of push at 0.5 MPa, whereas stepping up to the 125 mm bore yields 6136 N. This model includes a PT1/2 port and a 25 mm rod with an M20x1.5 thread. Because the 450 mm stroke creates a long lever arm, an external guide is recommended to prevent rod-bearing bending under heavy side loads.
As a standard ISO 15552 cylinder, it serves as a drop-in replacement sharing standardized mounting interface dimensions with other ISO 15552 profile cylinders. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold a load. If unpowered drift poses a risk, use a BSE rod lock.
Quick checklist
This 100 mm bore cylinder features a PT1/2 port and a 25 mm rod. It delivers 3927 N push and 3681 N pull at 0.5 MPa, 5497 N push at 0.7 MPa, and reaches a maximum of 801 kgf at 1.0 MPa.
No, the adjustable air cushion only decelerates the piston near the stroke end and is not a locking mechanism. If the air supply is lost or the valve is centered, the rod will drift. For true position holding, consider an AirTAC BSE series rod lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.