The AirTAC AirTAC SE100X460S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 460mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X460S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty positioning. It provides a substantial 3927 N push force at 0.5 MPa and a 460 mm stroke, making it well-suited for high-inertia automation sequences.
Its square extruded aluminum barrel lacks external tie rods, yielding a flush exterior that simplifies flush mounting and resists corrosion. The integrated -S magnet enables position detection via CMSE reed or DMSE electronic sensors, while field-adjustable pneumatic cushioning at both ends allows you to fine-tune end-of-stroke deceleration for heavy payloads.
| Model | AirTAC SE100X460S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 460 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×460 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 5497 N thrust at 0.7 MPa needed to form and stamp steel door panels, utilizing the 460 mm stroke to fully clear the lower die for robotic loading.
Shifts heavy 801 kgf max loads of inbound pallets onto parallel packaging lines, relying on the adjustable end cushions to soften stops at high cycle rates.
Drives the knockout plate for large plastic bins, using the built-in magnet with DMSE solid-state sensors to confirm full part ejection before the mold closes.
If 3927 N of push at 0.5 MPa is more than your application requires, stepping down to the 80 mm bore yields 2513 N, saving valuable compressed air. Conversely, if you need greater thrust, the 125 mm bore provides 6136 N at 0.5 MPa. Because this is a 460 mm stroke unit, the unsupported length of the 25 mm rod demands careful attention; for heavy off-center loads, incorporate an external guide to prevent rod-bearing bending and premature seal wear. As a dimensionally interchangeable ISO 15552 component, it serves as a direct drop-in replacement for other ISO 15552 profile cylinders using the same 100 mm bore, 460 mm stroke, PT1/2 port, and mounting hardware.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force reaches 5497 N. The maximum allowable push force is 801 kgf at 1.0 MPa.
No, the SE100X460S is a standard double-acting cylinder and will drift if air is exhausted or a valve is centered. The adjustable air cushions only decelerate the piston near the stroke ends; they do not lock the rod. For position holding, consider the BSE series with a rod lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.