The AirTAC AirTAC SE100X460SCA ISO 15552 Cylinder | 100mm is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 460mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X460SCA is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty motion tasks. Operating at 0.5 MPa, it delivers a substantial 3927 N push force and 3681 N pull force, utilizing a Ø25 mm piston rod with an M20x1.5 thread. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while simplifying sensor placement along its three integrated grooves.
This specific configuration includes a CA single clevis mounting accessory and a built-in magnet (S) for position detection via AirTAC CMSE reed or DMSE electronic sensors. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a screw, softening hard impacts during high-speed 460 mm strokes without relying on fixed rubber bumpers.
| Model | AirTAC SE100X460SCA ISO 15552 Cylinder | 100mm |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 460 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×460 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 3927 N push at 0.5 MPa required to flatten and seal heavy corrugated cartons over a 460 mm travel distance on automated packaging lines.
Drives heavy mold ejection plates with a Ø25 mm rod and M20x1.5 thread, utilizing the CA clevis to accommodate slight angular misalignment during part extraction.
Applies up to 801 kgf at 1.0 MPa for light-duty bending and straightening of sheet metal brackets, absorbing end-of-stroke energy via the adjustable cushion.
Generating 3927 N of push force at 0.5 MPa, this 100 mm bore cylinder sits perfectly between the 80 mm model (2513 N push) and the 125 mm model (6136 N push) if you need to step down for energy efficiency or up for heavier loads. Because the 460 mm stroke exceeds the 300 mm threshold, the unsupported rod length increases susceptibility to bending under side loads; integrating an external guide rail is strongly recommended to prevent premature rod-bearing wear. Remember that the adjustable air cushion only decelerates the piston near stroke end—it is not a locking mechanism, so a BSE rod lock variant is required if the application must hold a vertical load without live air pressure.
Quick checklist
This 100 mm bore cylinder features a PT1/2 port and a Ø25 mm rod. It generates 3927 N push and 3681 N pull at 0.5 MPa, 5497 N push at 0.7 MPa, and reaches a maximum push force of 801 kgf at 1.0 MPa.
Yes, the SE100X460SCA is dimensionally interchangeable per ISO 15552 standards, allowing a drop-in replacement for other ISO 15552 profile cylinders using your existing mounting hardware and footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.