The AirTAC AirTAC SE100X475S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 475mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X475S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. It delivers a substantial 3927 N push force at 0.5 MPa and features a 475 mm stroke. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal mechanics.
Equipped with a built-in magnet (-S), this unit seamlessly integrates AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration via a set screw, absorbing kinetic energy smoothly across the 36 mm cushion length. This is a genuine deceleration system, not a static rubber bumper.
| Model | AirTAC SE100X475S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 475 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×475 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates heavy machining center pallet shuttles, utilizing the 3927 N push force to index loaded workholding fixtures securely.
Drives the main folding platen on large carton erecting machinery, where the 475 mm stroke accommodates oversized packaging formats.
Provides secondary knock-out force for heavy plastic injection molds, using the adjustable cushion to soften rapid retraction stops.
Select this 100 mm bore actuator when an application requires moving heavy payloads with a 475 mm travel range. If you need slightly less force, the 80 mm bore provides 2513 N of push at 0.5 MPa; stepping up to the 125 mm bore yields 6136 N for heavier masses. Because this is a 475 mm stroke, the 25 mm rod and its bearing face bending stress under high side loads—always support the load with an external guide rail to prevent premature seal wear.
As a standard ISO 15552 cylinder, the SE100X475S is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing direct retrofitting without changing mounting hardware. Note that a plain SE cylinder relies on live air pressure to hold position; if pneumatics fail, the piston drifts. For safety-critical holding, consider the BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force reaches 5497 N. The maximum push force is 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE100X475S is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing foot, flange, or trunnion mounts. The built-in -S magnet also allows direct mounting of AirTAC CMSE reed or DMSE electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.