The AirTAC AirTAC SE100X500 FTC ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 500mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X500FTC is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. It delivers a robust 3927 N push force at 0.5 MPa and features a 500 mm stroke. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames, while the integrated FTC accessory provides a rigid front trunnion mounting interface.
This 100 mm bore actuator uses a PT1/2 port and a Ø25 mm hard-chrome rod with an M20x1.5 thread. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard mechanical stops during high-speed 30-800 mm/s cycles. This specific SKU lacks the -S magnet, meaning it does not natively support CMSE or DMSE position sensors without modification.
| Model | AirTAC SE100X500 FTC ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 500 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Applies 3927 N of clamping force to hold heavy steel chassis panels during robotic spot-welding, using the 500 mm stroke to clear large work envelopes.
Leverages the 500 mm extension to push heavy unit loads from a high-speed packaging conveyor onto downstream sorting lanes without stalling.
Utilizes the rigid FTC front trunnion mount to withstand high lateral moments when pulling dense molded plastic parts out of deep tooling cavities.
Selecting this 100 mm bore actuator makes sense when your mechanism requires substantial thrust; stepping down to a 63 mm bore drops the 0.5 MPa push to 1559 N, while stepping up to a 125 mm bore increases it to 6136 N. Because the stroke is 500 mm, the unsupported rod length is substantial—always incorporate an external guide to prevent rod-bearing bending and premature seal wear under side loads.
As a true ISO 15552 profile cylinder, this model serves as a drop-in dimensional replacement for other ISO 15552 actuators, sharing identical mounting footprint and port locations. Keep in mind that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking device. If the machinery must hold a vertical load without continuous air pressure, pair this cylinder with an external pilot-operated check valve or specify the BSE rod-lock variant.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force is 5497 N. The maximum allowable push force is 801 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s.
This specific SKU lacks the built-in -S magnet, so it cannot natively host AirTAC CMSE or DMSE sensors without modification. Dimensionally, it is an ISO 15552 profile cylinder, making it a drop-in replacement for any other ISO 15552 actuator sharing the same 100 mm bore and FTC trunnion footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.