The AirTAC AirTAC SE100X50FTC ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 50mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X50FTC is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty positioning. It delivers a robust 3927 N push force at 0.5 MPa and features a 50 mm stroke. The extruded aluminum square barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames without protruding hardware.
This FTC-mounted unit relies on field-adjustable pneumatic cushioning at both ends to decelerate the 25 mm hard-chrome rod near stroke end. Note that this specific SKU lacks a built-in magnet, meaning it cannot host CMSE or DMSE position sensors without modification. The cushioning is a true adjustable air dashpot, not a static rubber bumper, allowing you to tune end-stop impact for high-speed cycles.
| Model | AirTAC SE100X50FTC ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 3927 N push force required to lower and hold heavy upper dies in metal fabrication press brakes, utilizing the 50 mm stroke for rapid tool clamping.
Breaks heavy injection molds open with 5497 N of extending force at 0.7 MPa, leveraging the FTC trunnion mount to absorb offset center-of-gravity loads during initial part ejection.
Actuates the heavy diverter gates on automated pallet dispensers, where the robust 25 mm rod handles the high inertia of moving loaded pallets over the short 50 mm stroke.
When sizing this 100 mm bore, compare its 3927 N push at 0.5 MPa against the 80 mm bore (2513 N push) if your load is lighter, or step up to the 125 mm bore (6136 N push) for heavier demands. Because this is a double-acting cylinder, it relies on live air pressure to move; it does not hold a load if air is exhausted or a valve centers, so add a BSE rod lock for fail-safe holding. The PT1/2 port and FTC center-trunnion mounting interface are dimensionally interchangeable with other ISO 15552 cylinders for direct retrofits.
Quick checklist
The SE100X50FTC generates 3927 N push and 3681 N pull at 0.5 MPa, 5497 N push at 0.7 MPa, and a maximum push of 801 kgf at 1.0 MPa. It uses a PT1/2 port and a 25 mm rod with an M20x1.5 thread.
Yes, the SE100X50FTC is dimensionally interchangeable per ISO 15552 standards. You can drop it in to replace other ISO 15552 profile cylinders using the same FTC mounting hardware and PT1/2 port connections.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.