The AirTAC AirTAC SE100X50SH ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 50mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X50SH is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a robust 3927 N push force at 0.5 MPa. It features a 100 mm bore and a 50 mm stroke, engineered with an extruded aluminum barrel that omits external tie rods for a flush, corrosion-resistant exterior. The integrated FKM (Viton) seal extends the operating temperature range up to 150 C, making it highly suitable for heated environments.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic position sensors along the three integrated sensor grooves. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when moving heavy loads at speeds up to 800 mm/s.
| Model | AirTAC SE100X50SH ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 5497 N push force at 0.7 MPa needed to secure heavy injection mold halves, utilizing its 50 mm stroke for rapid, high-force actuation.
Handles the lateral redirection of heavy loaded pallets on a packaging line, where the Viton seal survives ambient heat from nearby shrink-wrap tunnels.
Drives heavy-duty bearings into automotive housings on an assembly line, relying on adjustable end cushions to prevent shock damage during the 50 mm stroke.
Choosing this 100 mm bore makes sense when you need substantial thrust; if you require less force, stepping down to the 80 mm bore yields 2513 N push at 0.5 MPa, while stepping up to the 125 mm bore provides 6136 N. Because this is a double-acting cylinder, it will drift if air pressure is lost or the valve centers, so a BSE rod lock variant is required for fail-safe load holding. As a dimensionally interchangeable ISO 15552 cylinder with a PT1/2 port and M20x1.5 rod thread, it serves as a direct drop-in replacement for standard profile cylinders using existing mounting hardware.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE100X50SH is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. It shares the standardized mounting interface and PT1/2 port, allowing it to drop directly into existing foot, flange, or trunnion hardware without machining.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.