The AirTAC AirTAC SE100X530S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 530mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X530S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics, delivering a robust 3927 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a highly corrosion-resistant body that mounts flush against machine frames without protruding hardware.
This 100mm bore unit includes a built-in magnet (-S) compatible with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable pneumatic cushioning at both ends allows you to tune the end-of-stroke deceleration via a set screw, softening hard impacts when moving heavy loads at speed.
| Model | AirTAC SE100X530S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 530 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×530 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 3927 N push force required to position heavy upper press brake tooling across a 530mm stroke in metal fabrication lines.
Actuates heavy pallet diverter arms on packaging conveyors, using the built-in magnet to trigger DMSE sensors for timed lane routing.
Drives robust extraction arms for automotive injection molded parts, relying on adjustable end cushions to soften deceleration.
This 100mm bore generates 3927 N push at 0.5 MPa. If your application requires less force, the 80mm bore neighbor provides 2513 N push, while stepping up to the 125mm bore yields 6136 N for heavier demands. Because this is a 530mm stroke, the 25mm rod and bearing face significant bending moments under side loads; an external guide rail is strongly recommended to prevent premature seal wear.
As a standard ISO 15552 cylinder, it is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing you to retrofit existing machinery using the same mounting hardware and PT1/2 port. Note that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure is lost. For position holding, use a BSE rod lock.
Quick checklist
At 0.5 MPa, the SE100X530S delivers 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa operating pressure.
No, the adjustable air cushion only decelerates the piston near the stroke end and is not a locking mechanism. If air is lost, the load will drift. For secure position holding, consider the AirTAC BSE series with a rod lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.