The AirTAC AirTAC SE100X55S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 55mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X55S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty motion. It delivers a robust 3927 N push force at 0.5 MPa and up to 5497 N at 0.7 MPa, utilizing a 100 mm bore and 55 mm stroke. The integrated -S magnet enables precise end-of-stroke detection when paired with AirTAC CMSE reed or DMSE electronic sensors.
Its extruded aluminum barrel omits external tie rods entirely, yielding a compact, corrosion-resistant housing that mounts flush against machine frames. Field-adjustable pneumatic cushioning at both stroke ends allows technicians to fine-tune deceleration via a set screw, softening hard mechanical stops during high-speed 30-800 mm/s cycles.
| Model | AirTAC SE100X55S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 55 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×55 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 3927 N of extend force at 0.5 MPa to secure large injection mold halves during plastic part cooling cycles.
Drives heavy press brake upper tooling with precise 55 mm travel, relying on the 25 mm hard-chrome rod to handle high side loads.
Actuates heavy pallet stacking fingers in automated packaging lines, using the built-in magnet for DMSE sensor feedback.
Stepping down to the 80 mm bore reduces the 0.5 MPa push output to 2513 N, while stepping up to the 125 mm bore increases it to 6136 N. When sizing this actuator, remember that the double-acting design relies on continuous air pressure; if air is lost or the valve centers, the piston drifts and cannot hold a load—use a BSE rod lock for fail-safe positioning. For ISO 15552 dimensional retrofitting, match the 100 mm bore, 55 mm stroke, PT1/2 port, and your required mounting accessory alongside the -S magnet.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, its mounting dimensions are interchangeable per ISO 15552 standards, allowing a drop-in retrofit for other profile cylinders. However, it does not hold position when air is exhausted; the adjustable cushion only decelerates the piston near stroke end rather than locking it.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.