The AirTAC AirTAC SE100X600FTC ISO 15552 Cylinder | 100mm is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 600mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X600FTC is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. It delivers a substantial 3927 N push force at 0.5 MPa and reaches a maximum push of 801 kgf at 1.0 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This 100mm bore unit features a 600mm stroke and an integrated FTC front trunnion mounting configuration. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration for high-speed loads. Note that this specific SKU lacks a built-in magnet, meaning it will not trigger CMSE or DMSE position sensors without modification.
| Model | AirTAC SE100X600FTC ISO 15552 Cylinder | 100mm |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives a 600mm stroke to position heavy strapping heads over large pallet loads, utilizing the 3927 N push force to ensure tight, secure banding.
Shifts heavy parcel diverter arms along sorting lines, relying on the FTC mount to handle high pivot stresses during rapid direction changes.
Actuates secondary ejection arms for large automotive molds, using the adjustable end cushions to soften the impact of 801 kgf peak forces at high speeds.
If your application requires slightly less force, the neighboring 80mm bore cylinder provides a 2513 N push at 0.5 MPa. Conversely, stepping up to the 125mm bore yields a 6136 N push for heavier payloads. Because this 600mm stroke generates significant lever arm forces on the Ø25mm rod and front bearing, an external guide is strongly recommended to prevent side-load bending and premature seal wear.
As a dimensionally interchangeable ISO 15552 cylinder, this model serves as a drop-in replacement for other standard profile cylinders. To match this exact configuration, specify a 100mm bore, 600mm stroke, PT1/2 port, FTC mounting accessory, and no sensor magnet. Keep in mind that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure is lost.
Quick checklist
At 0.5 MPa, this 100mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force is 5497 N. The maximum push capacity is 801 kgf at 1.0 MPa operating pressure.
It is dimensionally interchangeable with other ISO 15552 profile cylinders, making it a drop-in retrofit for standard footprints. However, the adjustable air cushion only decelerates the piston near stroke end and does not function as a brake; it will not hold a load if air pressure is lost.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.