The AirTAC AirTAC SE100X600S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 600mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X600S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 3927 N push force at 0.5 MPa and a maximum 801 kgf output at 1.0 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal mechanics.
Equipped with a built-in magnet (-S), this 100 mm bore unit seamlessly integrates AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-velocity 600 mm extensions.
| Model | AirTAC SE100X600S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 3927 N push at 0.5 MPa needed to deflect heavy loaded pallets from a main conveyor line onto a secondary packaging spur over its 600 mm extension.
Drives large molded plastic parts out of an injection molding press, utilizing the 36 mm adjustable air cushion to safely decelerate the 25 mm rod at high cycling speeds.
Feeds heavy-diameter bar stock through a CNC lathe spindle, relying on DMSE electronic sensors to confirm the full 600 mm retraction before the chuck closes.
Selecting the SE100X600S makes sense when substantial thrust is required over a long reach; it provides 3927 N push at 0.5 MPa. If your application demands less force, stepping down to the 80 mm bore yields 2513 N push, whereas stepping up to the 125 mm bore provides 6136 N push for heavier payloads. Because this model features a 600 mm stroke, the 25 mm rod and rod-end bearing face increased bending moments under side loads, making an external guide rail essential to prevent premature seal wear.
This cylinder serves as a dimensionally interchangeable drop-in replacement for other ISO 15552 profile cylinders, matching the 100 mm bore, 600 mm stroke, PT1/2 port, and standardized mounting accessories exactly. Remember that the adjustable air cushion only decelerates the piston near stroke end and does not function as a locking device; if the load must be held vertically without live air pressure, integrate a BSE rod lock or external pilot-operated check valve.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N, with a maximum push capacity of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552, matching standard mounting footprints and PT1/2 ports for direct retrofitting. However, the adjustable air cushion only decelerates the piston near stroke end and does not hold position; you must use a BSE rod lock or external check valve to prevent drift when air pressure is lost.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.